Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 77
2.1.2
Component Location Overview - Rear Control Modules
1 - Auxiliary Engine Coolant
Heater Radio Frequency Re‐
ceiver - R149-
❑ Removing and instal‐
ling. Refer to ⇒ Heating,
Ventilation and Air Con‐
ditioning.; Rep. Gr. 82 ;
Additional Components
for Control and Regula‐
tion; Auxiliary Engine
Coolant Heater Radio
Frequency Receiver -
R149- Removing and
Installing
2 - Mobile Communication 2-
Way Signal Amplifier - J984-
❑ Removing and instal‐
ling. Refer to ⇒ Com‐
munication; Rep. Gr.
91 ; Telephone System;
Component Location
Overview - Telephone
System .
3 - Engine Sound Generator
Control Module - J943-
❑ Not installed
4 - Bolt
❑ Not installed
5 - Electronic Damping Control
Module - J250-
❑ Overview. Refer to ⇒
Suspension, Wheels,
Steering; Rep. Gr. 43 ;
Electronic Damping;
Overview - Electronic
Damping .
6 - Towing Recognition Control Module - J345-
❑ Removing and installing. Refer to
⇒ “12.3 Towing Recognition Control Module J345 , Removing and Installing”, page 215
.
2.2
Overview - Control Modules
1 - Parking Aid Control Module
- J446- / Parallel Parking As‐
sistance Control Module -
J791-
❑ With parking aid: Park‐
ing Aid Control Module -
J446-
❑ Overview. Refer to
.
❑ With parallel parking as‐
sist: Parallel Parking As‐
sistance Control Module
- J791-
❑ Overview. Refer to
2 - Bracket
❑ For Parking Aid Control
Module - J446- / Parallel
Parking Assistance
Control Module - J791-
❑ Removing and instal‐
ling. Refer to
.
3 - Bracket
❑ For Vehicle Electrical
System Control Module
- J519-
❑ Removing and instal‐
ling. Refer to
⇒ “2.6 Vehicle Electrical System Control Module J519 Bracket, Removing and Installing”, page 301
4 - Vehicle Electrical System Control Module - J519-
❑ Removing and installing. Refer to
⇒ “2.4 Vehicle Electrical System Control Module J519 , Removing and Installing”, page 299
5 - Guide
❑ For the center connector
2.3
Overview - Data Bus On Board Diagnostic Interface
1 - Connector
❑ For Data Bus On Board
Diagnostic Interface -
J533-
2 - Data Bus On Board Diag‐
nostic Interface - J533-
❑ Removing and instal‐
ling. Refer to
.
3 - Bolt
❑ Tightening specifica‐
tion. Refer to ⇒ Body
Interior; Rep. Gr. 70 ;
Instrument Panel Cen‐
tral Tube; Overview - In‐
strument Panel Central
Tube .
4 - Crash Bracket
❑ Overview. Refer to ⇒
Body Interior; Rep. Gr.
70 ; Instrument Panel
Central Tube; Overview
- Instrument Panel Cen‐
tral Tube .
5 - Instrument Panel Central
Tube
2.4
Vehicle Electrical System Control Mod‐
ule - J519- , Removing and Installing
If the control module is being replaced, use the Vehicle Diagnostic
Tester and select the “Replacing” function for the respective con‐
trol module in “Guided Fault Finding”.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the A-pillar lower trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Passenger Compartment Trim; A-Pillar Trim
Panel, Removing and Installing .
– Remove the footwell cover on the driver side. Refer to ⇒ Body
Interior; Rep. Gr. 68 ; Storage Compartments and Covers;
Driver Side Footwell Cover, Removing and Installing .
– Release and disconnect the connectors -1, 2, and 3-.
– To disconnect the connector press the circlip -1-.
– Pivot the retaining bracket in direction of -arrow- and remove
the connector.
– Release the springs -arrow-, pivot the Vehicle Electrical Sys‐
tem Control Module - J519- -4- out of the bracket -5- and
remove downward.
Installing
Install in reverse order of removal.
2.5
Data Bus On Board Diagnostic Interface
- J533- , Removing and Installing
If the control module is being replaced, use the Vehicle Diagnostic
Tester and select the “Replacing” function for the respective con‐
trol module in “Guided Fault Finding”.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст