Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 870
♦ Seal Installer - Camshaft
Installer Kit - Sleeve -
3241/4-
♦ Puller - Grease Cap -
VW637/2-
♦ Torque Wrench 1332
40-200Nm - VAG1332-
♦ Socket - XZN 18mm -
T10162A-
♦ Torque Wrench 1410 -
VAG1410-
♦ Shock Absorber Set - T10001-
♦ Bearing Installer - Wheel Hub/Bearing Kit - T10205A-
♦ Socket AF 24 mm - T10361A-
♦ Drive Shaft Remover - T10520-
♦ Digital Torque Wrench - VAG1756A-
43 – Level Control System
1
Electronic Damping
⇒ “1.1 Overview - Electronic Damping”, page 267
⇒ “1.2.1 Electronic Damping Control Module J250 , Removing
and Installing, Golf”, page 272
⇒ “1.3 Left/Right Front Body Acceleration Sensor G341 / G342 ,
Removing and Installing”, page 274
⇒ “1.4 Left Rear Body Acceleration Sensor G699 , Removing and
1.1
Overview - Electronic Damping
⇒ “1.1.1 Overview - Electronic Damping, Torsion Beam Axle,
Golf”, page 267
⇒ “1.1.2 Overview - Electronic Damping, Multi-Link Suspension,
Golf”, page 269
⇒ “1.1.3 Overview - Electronic Damping, Multi-Link Suspension,
1.1.1
Overview - Electronic Damping, Torsion Beam Axle, Golf
1 - Right Front Level Control
Sensor - G289-
❑ Removing and instal‐
ling. Refer to
2 - Right Front Body Accelera‐
tion Sensor - G342-
❑ Removing and instal‐
ling. Refer to
3 - Left Rear Body Acceleration
Sensor - G699-
❑ Component location: in
the luggage compart‐
ment on the left shock
absorber tower behind
the left side trim panel
❑ Removing and instal‐
ling. Refer to
4 - Electronic Damping Control
Module - J250-
❑ Removing and instal‐
ling. Refer to
ule J250 , Removing and Installing, Golf”, page 272
❑ Component location: the Electronic Damping Control Module - J250- is installed in the luggage com‐
partment behind the left side trim panel.
❑ If the Electronic Damping Control Module - J250- is being replaced, the
Replace Control Module
function must be performed using the Vehicle Diagnostic Tester .
❑ If the control position was reprogrammed and if the vehicle has lane assist, then the front camera for the
driver assistance systems must be calibrated.
5 - Left Rear Level Control System Sensor - G76-
❑ Removing and installing. Refer to
⇒ “2.4.1 Left Rear Level Control System Sensor G76 , Removing and Installing, Torsion Beam Axle”,
6 - Left Front Body Acceleration Sensor - G341-
❑ Removing and installing. Refer to
⇒ “1.3 Left/Right Front Body Acceleration Sensor G341 / G342 , Removing and Installing”, page 274
7 - Left Front Level Control System Sensor - G78-
❑ Removing and installing. Refer to
⇒ “2.3 Left/Right Front Level Control System Sensor G78 / G289 , Removing and Installing”,
8 - Shock Absorber with Right Front Damping Adjustment Valve - N337-
❑ Removing and installing the suspension strut. Refer to
⇒ “3.2 Suspension Strut, Removing and Installing”, page 45
.
❑ Servicing the suspension strut. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст