Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 90
Monitor-ID $A3: Misfire Cylinder 2 Data
– Connect the scan tool.
– Start the engine and run at idle.
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
Select “Monitor-ID $A3”.
– Select the desired “Test-ID” or “Hex-ID”.
– Check specified values at idle.
Test-ID
DTC
Component or System
Min.
Max.
Additional Information
$0B
P0302 Misfire Cylinder 2, Average Value
Over 10 Driving Cycles.
0.0
counts
65,535.
0 counts
Refer to DTC P0302 in the
DTC summary table.
$0C
P0302 Misfire Cylinder 2, In This Driving Cy‐
cle.
0.0
counts
65,535.
0 counts
Refer to DTC P0302 in the
DTC summary table.
– If any of components or systems fail to meet the specified val‐
ues. Refer to Diagnostic “Mode 03: Interrogating Fault Mem‐
ory” to check for stored DTC's or the corresponding diagnostic
repair procedure
⇒ “3.3.3 Diagnostic Mode 03 - Read DTC Memory”,
– Switch the ignition OFF.
Monitor-ID $A4: Misfire Cylinder 3 Data
– Connect the scan tool.
– Start the engine and run at idle.
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
Select “Monitor-ID $A4”.
– Select the desired “Test-ID” or “Hex-ID”.
– Check specified values at idle.
Test-ID
DTC
Component or System
Min.
Max.
Additional Information
$0B
P0303 Misfire Cylinder 3, Average Value
Over 10 Driving Cycles.
0.0
counts
65,535.
0 counts
Refer to DTC P0303 in the
DTC summary table.
$0C
P0303 Misfire Cylinder 3, In This Driving Cy‐
cle.
0.0
counts
65,535.
0 counts
Refer to DTC P0303 in the
DTC summary table.
– If any of components or systems fail to meet the specified val‐
ues. Refer to Diagnostic “Mode 03: Interrogating Fault Mem‐
ory” to check for stored DTC's or the corresponding diagnostic
repair procedure
⇒ “3.3.3 Diagnostic Mode 03 - Read DTC Memory”,
– Switch the ignition OFF.
Monitor-ID $A5: Misfire Cylinder 4 Data
– Connect the scan tool.
– Start the engine and run at idle.
GTI 2014 ➤
Generic Scan Tool - Edition 04.2015
3. Diagnosis and Testing
33
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
Select “Monitor-ID $A5”.
– Select the desired “Test-ID” or “Hex-ID”.
– Check specified values at idle.
Test-ID
DTC
Component or System
Min.
Max.
Additional Information
$0B
P0304 Misfire Cylinder 4, Average Value
Over 10 Driving Cycles.
0.0
counts
65,535.
0 counts
Refer to DTC P0304 in the
DTC summary table.
$0C
P0304 Misfire Cylinder 4, In This Driving Cy‐
cle.
0.0
counts
65,535.
0 counts
Refer to DTC P0304 in the
DTC summary table.
– Switch the ignition OFF.
– If any of components or systems fail to meet the specified val‐
ues. Refer to Diagnostic “Mode 03: Interrogating Fault Mem‐
ory” to check for stored DTC's or the corresponding diagnostic
repair procedure
⇒ “3.3.3 Diagnostic Mode 03 - Read DTC Memory”,
.
3.3.7
Diagnostic Mode 06 - Read Test Results
for Specific Diagnostic Functions, 2016
MY
Diagnostic Mode 06 makes it possible to retrieve test results for
special components and systems which are continuously or not
continuously monitored. If the diagnosis of a system is complete,
the diagnostic result and the corresponding thresholds are saved
and displayed in mode 06. This data remains saved (even with
the ignition off) until either new diagnostic results become avail‐
able or the DTC memory is erased.
The min & max values for each individual test in Mode 06 repre‐
sent the min & max operating values for a properly operating
system. This data is provided to the individual aftermarket scan
tool companies for development of their scan tool. Depending on
the scan tool being used, the min & max values shown may vary,
or be rounded up or down to the nearest decimal point depending
on the aftermarket scan tool company's development process.
For example; GST manual documentation will show the value as
0.3499 (units) while the scan tool will display the same value as
0.35 (units).
Depending on the scan tool and protocol used, the information
displayed in Diagnostic Mode 06 may be referred to by different
names such as Test-ID (TID), Hex-ID, Component-ID (CID), On-
Board Diagnostic Monitor Identifier (OBDMID), or contain no
name at all and may be referenced by only a number.
Test requirements
• Exhaust system must be properly sealed between the catalytic
converter and the cylinder heads.
• No DTCs stored in the DTC memory.
• Coolant temperature at least 80 °C.
Work procedure
– Connect the scan tool.
GTI 2014 ➤
Generic Scan Tool - Edition 04.2015
34
Rep. Gr. ST - Generic Scan Tool
– Start the engine and let run at idle speed.
– Select Mode 6: Check test the results of components that are
not continuously monitored.
Select the desired Test-ID.
The current minimum and maximum values will be displayed on
the scan tool screen.
The following table is a numerical list of all“Test-IDs” that may be
selected.
Monitor-ID
Component or System
$01:
Oxygen Sensor Monitor Bank 1 – Sensor 1
$02:
Oxygen Sensor Monitor Bank 1 – Sensor 2
$21:
Catalytic Converter Monitoring
$35:
Camshaft Adjustment Bank 1
$3C:
Tank Venting System Leak Test (0.020" / 0.5 mm)
$3D:
Tank Vent Valve Function Check
$41:
O2 Sensor Heater Bank 1 – Sensor 1
$42:
O2 Sensor Heater Bank 1 – Sensor 2
$71:
Secondary Air System Bank 1
$A2:
Misfire Cylinder 1 Data
$A3:
Misfire Cylinder 2 Data
$A4:
Misfire Cylinder 3 Data
$A5:
Misfire Cylinder 4 Data
Monitor-ID $01: Oxygen Sensor Monitor Bank 1 – Sensor 1
– Connect the scan tool.
– Start the engine and run at idle.
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
Select “Monitor-ID $01”.
– Select the desired “Test-ID” or “Hex-ID”.
– Check specified values at idle.
Test-ID
DTC
Component or System
Min.
Max.
Additional Information
$83
P0133 Oxygen Sensor Dynamic Test Bank
1, Sensor 1.
0.0 V
1.0996
V
Refer to DTC P0133 in the
DTC summary table.
$86
P0133 Oxygen Sensor Dynamic Test Bank
1, Sensor 1.
0.0 V
1.0996
V
Refer to DTC P0133 in the
DTC summary table.
$8A
P2195 Oxygen Sensor Intrusive Check
0.89
32.767 Refer to DTC P2195 in DTC
$8B
P2196 Oxygen Sensor Intrusive Check
0.89
32.767 Refer to DTC P2196 in the
DTC summary table.
– If any of components or systems fail to meet the specified val‐
ues. Refer to Diagnostic “Mode 03: Interrogating Fault Mem‐
ory” to check for stored DTC's or the corresponding diagnostic
repair procedure
GTI 2014 ➤
Generic Scan Tool - Edition 04.2015
3. Diagnosis and Testing
35
⇒ “3.3.3 Diagnostic Mode 03 - Read DTC Memory”,
.
– Switch the ignition OFF.
Monitor-ID $02: Oxygen Sensor Monitor Bank 1 – Sensor 2
– Connect the scan tool.
– Start the engine and run at idle.
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
Select “Monitor-ID $02”.
– Select the desired “Test-ID” or “Hex-ID”.
– Check specified values at idle.
Test-ID DTC
Component or System
Min.
Max.
Additional Information
$05
P013A Oxygen Sensor Transition Time.
900.0
mV/s
65,534.
0 mV/s
Refer to DTC P013A in the
DTC summary table.
$92
P013B Oxygen Sensor Maximum Gradient Of
Sensor Signal During Lean – Rich –
Transition.
650.0
mV/s
65,534.
0 mV/s
Refer to DTC P013B in the
DTC summary table.
$93
P013E Oxygen Sensor Dynamic Test, Delay
Rich To Lean.
0.0 s
0.9 s
Refer to DTC P013E in the
DTC summary table.
$94
P013F Oxygen Sensor Dynamic Test, Delay
Lean To Rich.
0.0 s
NaN
Refer to DTC P013F in the
DTC summary table.
$95
P2270 Oxygen Sensor Target Voltage In Fat
Mode Not Reached.
0.874 V 7.999 V Refer to DTC P2270 in the
DTC summary table.
$96
P2271 Oxygen Sensor Target Voltage In
Lean-Burn Mode Not Reached.
0.0 V 0.249 V Refer to DTC P2271 in the
DTC summary table.
– If any of components or systems fail to meet the specified val‐
ues. Refer to Diagnostic “Mode 03: Interrogating Fault Mem‐
ory” to check for stored DTC's or the corresponding diagnostic
repair procedure
⇒ “3.3.3 Diagnostic Mode 03 - Read DTC Memory”,
.
– Switch the ignition OFF.
Monitor-ID $21: Catalytic Converter Monitoring
– Connect the scan tool.
– Start the engine and run at idle.
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
Select “Monitor-ID $21”.
– Select the desired “Test-ID” or “Hex-ID”.
– Check specified values at idle.
Test-ID
DTC
Component or System
Min.
Max.
Additional Information
$84
P0420 Catalytic Converter Assessment Of
Oxygen Storage Capacity (OSC) Com‐
pared To Catalytic Converter Map.
0.0
OSC
1.0 OSC Refer to DTC P0420 in the
DTC summary table.
GTI 2014 ➤
Generic Scan Tool - Edition 04.2015
36
Rep. Gr. ST - Generic Scan Tool
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст