Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 91
– If any of components or systems fail to meet the specified val‐
ues. Refer to Diagnostic “Mode 03: Interrogating Fault Mem‐
ory” to check for stored DTC's or the corresponding diagnostic
repair procedure
⇒ “3.3.3 Diagnostic Mode 03 - Read DTC Memory”,
– Switch the ignition OFF.
Monitor-ID $35: Camshaft Adjustment Bank 1
– Connect the scan tool.
– Start the engine and run at idle.
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
Select “Monitor-ID $35”.
– Select the desired “Test-ID” or “Hex-ID”.
– Check specified values at idle.
Test-ID
DTC
Component or System
Min.
Max.
Additional Information
$80
P0011 VVT Intake Camshaft Diagnosis, Tar‐
get Position Not Reached, Target Er‐
ror.
0.0°
CRK
10.0°
CRK
Refer to DTC P0011 in the
DTC summary table.
$81
P000A VVT Intake Camshaft Diagnosis,
Specified Position Reached Too
Slowly, Slow Response.
10.0°
CRK
655.35°
CRK
Refer to DTC P000A in the
DTC summary table.
$82
P0014 VVT Exhaust Camshaft Diagnosis,
Target Position Not Reached, Target
Error.
0.0°
CRK
10.0°
CRK
Refer to DTC P0014 in the
DTC summary table.
$83
P000B VVT Exhaust Camshaft Diagnosis,
Specified Position Reached Too
Slowly, Slow Response.
3.5°
CRK
655.35°
CRK
Refer to DTC P000B in the
DTC summary table.
– If any of components or systems fail to meet the specified val‐
ues. Refer to Diagnostic “Mode 03: Interrogating Fault Mem‐
ory” to check for stored DTC's or the corresponding diagnostic
repair procedure
⇒ “3.3.3 Diagnostic Mode 03 - Read DTC Memory”,
– Switch the ignition OFF.
Monitor-ID $3C: Tank Venting System Leak Test (0.020" / 0.5
mm)
– Connect the scan tool.
– Start the engine and run at idle.
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
Select “Monitor-ID $3C”.
– Select the desired “Test-ID” or “Hex-ID”.
– Check specified values at idle.
Test-ID
DTC
Component or System
Min.
Max.
Additional Information
$83
P0456 NVLD Fine Leak Detection.
10.0
65,535.
0
Refer to DTC P0456 in the
DTC summary table.
GTI 2014 ➤
Generic Scan Tool - Edition 04.2015
3. Diagnosis and Testing
37
– If any of components or systems fail to meet the specified val‐
ues. Refer to Diagnostic “Mode 03: Interrogating Fault Mem‐
ory” to check for stored DTC's or the corresponding diagnostic
repair procedure
⇒ “3.3.3 Diagnostic Mode 03 - Read DTC Memory”,
.
– Switch the ignition OFF.
Monitor-ID $3D: Tank Vent Valve Function Check
– Connect the scan tool.
– Start the engine and run at idle.
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
Select “Monitor-ID $3D”.
– Select the desired “Test-ID” or “Hex-ID”.
– Check specified values at idle.
Test-ID
DTC
Component or System
Min.
Max.
Additional Information
$8B
P0441 Tank Vent Valve – Function Check,
Test Using Cross-Correlation.
0.1
655.35 Refer to DTC P0441 in the
DTC summary table.
$92
P0441 Tank Vent Valve – Function Check,
Quick Check
0.399
1.999 Refer to DTC P0441 in the
DTC summary table.
– If any of components or systems fail to meet the specified val‐
ues. Refer to Diagnostic “Mode 03: Interrogating Fault Mem‐
ory” to check for stored DTC's or the corresponding diagnostic
repair procedure
⇒ “3.3.3 Diagnostic Mode 03 - Read DTC Memory”,
.
– Switch the ignition OFF.
Monitor-ID $41: O2 Sensor Heater Bank 1 – Sensor 1
– Connect the scan tool.
– Start the engine and run at idle.
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
Select “Monitor-ID $41”.
– Select the desired “Test-ID” or “Hex-ID”.
– Check specified values at idle.
Test-ID
DTC
Component or System
Min.
Max.
Additional Information
$85
P0135 Oxygen Sensor Ceramic Tempera‐
ture Monitoring.
630.0° C 6,513.5°
C
Refer to DTC P0135 in the
DTC summary table.
– If any of components or systems fail to meet the specified val‐
ues. Refer to Diagnostic “Mode 03: Interrogating Fault Mem‐
ory” to check for stored DTC's or the corresponding diagnostic
repair procedure
⇒ “3.3.3 Diagnostic Mode 03 - Read DTC Memory”,
.
GTI 2014 ➤
Generic Scan Tool - Edition 04.2015
38
Rep. Gr. ST - Generic Scan Tool
– Switch the ignition OFF.
Monitor-ID $42: O2 Sensor Heater Bank 1 – Sensor 2
– Connect the scan tool.
– Start the engine and run at idle.
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
Select “Monitor-ID $42”.
– Select the desired “Test-ID” or “Hex-ID”.
– Check specified values at idle.
Test-ID
DTC
Component or System
Min.
Max.
Additional Information
$90
P0141 Oxygen Sensor Nernst Cell Resist‐
ance Test.
0.0 Ω
700.0 Ω Refer to DTC P0141 in the
DTC summary table.
– If any of components or systems fail to meet the specified val‐
ues. Refer to Diagnostic “Mode 03: Interrogating Fault Mem‐
ory” to check for stored DTC's or the corresponding diagnostic
repair procedure
⇒ “3.3.3 Diagnostic Mode 03 - Read DTC Memory”,
– Switch the ignition OFF.
Monitor-ID $71: Secondary Air System Bank 1
– Connect the scan tool.
– Start the engine and run at idle.
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
Select “Monitor-ID $71”.
– Select the desired “Test-ID” or “Hex-ID”.
– Check specified values at idle.
Test-ID
DTC
Component or System
Min.
Max.
Additional Information
$82
P0491 System Testing, Reduced Secon‐
dary Air Mass.
0.0
1.999 Refer to DTC P0491 in the
DTC summary table.
$85
P0410 System Testing Of Pressure Sensor. 0.0 kPa 5.0 kPa Refer to DTC P0410 in the
DTC summary table.
$8C
P2440 Functional Testing Of Secondary Air
Valve, Valve Leak Check.
0.0
1.34
Refer to DTC P2440 in the
DTC summary table.
– If any of components or systems fail to meet the specified val‐
ues. Refer to Diagnostic “Mode 03: Interrogating Fault Mem‐
ory” to check for stored DTC's or the corresponding diagnostic
repair procedure
⇒ “3.3.3 Diagnostic Mode 03 - Read DTC Memory”,
– Switch the ignition OFF.
Monitor-ID $A2: Misfire Cylinder 1 Data
– Connect the scan tool.
GTI 2014 ➤
Generic Scan Tool - Edition 04.2015
3. Diagnosis and Testing
39
– Start the engine and run at idle.
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
Select “Monitor-ID $A2”.
– Select the desired “Test-ID” or “Hex-ID”.
– Check specified values at idle.
Test-ID
DTC
Component or System
Min.
Max.
Additional Information
$0B
P0301 Misfire Cylinder 1, Average Value
Over 10 Driving Cycles.
0.0
counts
65,535.
0 counts
Refer to DTC P0301 in the
DTC summary table.
$0C
P0301 Misfire Cylinder 1, In This Driving
Cycle.
0.0
counts
65,535.
0 counts
Refer to DTC P0301 in the
DTC summary table.
– If any of components or systems fail to meet the specified val‐
ues. Refer to Diagnostic “Mode 03: Interrogating Fault Mem‐
ory” to check for stored DTC's or the corresponding diagnostic
repair procedure
⇒ “3.3.3 Diagnostic Mode 03 - Read DTC Memory”,
.
– Switch the ignition OFF.
Monitor-ID $A3: Misfire Cylinder 2 Data
– Connect the scan tool.
– Start the engine and run at idle.
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
Select “Monitor-ID $A3”.
– Select the desired “Test-ID” or “Hex-ID”.
– Check specified values at idle.
Test-ID
DTC
Component or System
Min.
Max.
Additional Information
$0B
P0302 Misfire Cylinder 2, Average Value
Over 10 Driving Cycles.
0.0
counts
65,535.
0 counts
Refer to DTC P0302 in the
DTC summary table.
$0C
P0302 Misfire Cylinder 2, In This Driving Cy‐
cle.
0.0
counts
65,535.
0 counts
Refer to DTC P0302 in the
DTC summary table.
– If any of components or systems fail to meet the specified val‐
ues. Refer to Diagnostic “Mode 03: Interrogating Fault Mem‐
ory” to check for stored DTC's or the corresponding diagnostic
repair procedure
⇒ “3.3.3 Diagnostic Mode 03 - Read DTC Memory”,
.
– Switch the ignition OFF.
Monitor-ID $A4: Misfire Cylinder 3 Data
– Connect the scan tool.
– Start the engine and run at idle.
– Select “Diagnostic Mode 6: Check test the results of compo‐
nents that are not continuously monitored”.
GTI 2014 ➤
Generic Scan Tool - Edition 04.2015
40
Rep. Gr. ST - Generic Scan Tool
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст