Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 955
– Position the -VAS6350A- at distance -a- to the rear wheels.
• Dimension -a- = 1700 ± 2 mm
– Switch on the -VAS6350/2- with the
ON
button.
Display on the -VAS6350/2- :
• “- - - m”
Note
The laser is switched on at same time.
– Hold the -VAS6350/2- -2- flush against the catch bracket, as
shown in the illustration, for the distance measurement.
• The -VAS6350/2- must lie firmly against the catch bracket.
– Make sure the “laser beam” for the distance measurement
contacts the paddle on lower enlarged part -1-.
If that is not the case, correct the measuring paddle height using
the locking nuts on the -VAS6350/1- .
– Briefly press the
ON
button for distance measurement.
Display on the -VAS6350/2- :
• “1,700 m” (specified value: 1700 ± 2 mm).
– Repeat the measurement procedure from the left catch brack‐
et to measuring paddle on left rear wheel.
• The distance value must be the same on both sides.
If both measured values are not the same, adjust the -VAS6350A-
accordingly.
Note
The vehicle in the illustration is only a basic outline.
– Secure the Calibration Tool - Lane Change Calibration Tool -
VAS6350/4- to the Calibration Unit - VAS6350A- mount on the
rear left side.
• When installed correctly, the vehicle electrical system voltage
line must be connected at bottom left of calibration device (as
seen in direction of travel).
• Sedan dimension -a- = 606 mm (measured from the upper
edge of the calibration device to workshop floor).
• Wagon dimension -a- = 618 mm (measured from the upper
edge of the calibration device to workshop floor).
– The adjustment dimension is set with the measuring point
-arrow- on the base of the calibration device on the scale of
the steel ruler -1-.
• Left adjustment dimension for Sedan = 621 mm (read on
measuring scale -1-).
• Left adjustment dimension for Wagon = 678 mm (read on
measuring scale -1-).
– Connect the Calibration Tool - Lane Change Calibration Tool
Calibration Tool - Lane Change Calibration Tool - VAS6350/4-
to the vehicle electrical system voltage.
– Using the bubble level (level indicator) -arrow-, bring the Cal‐
ibration Unit - VAS6350A- into a horizontal position by turning
the plastic bases.
– Wear laser protective eyewear.
Note
The vehicle in the illustration is only a basic outline.
– Turn on the Calibration Laser - VAS6350/3A- on the Calibra‐
tion Unit - VAS6350A- .
– Align the entire Calibration Unit - VAS6350A- so that the laser
beam shines on the center of the vehicle rear above the VW
logo.
– Check right and left distance between catch bracket on the
Calibration Unit - VAS6350A- and measuring paddle -1- on
wheel mountings again.
• Specified value: 1700 ± 2 mm
Blind Spot Detection Control Module, Calibrating. Refer to
⇒ “13.4.3 Blind Spot Detection Control Module J1086 / Blind Spot
Detection Control Module 2 J1087 , Calibrating”, page 227
.
13.4.3
Blind Spot Detection Control Module -
J1086- / Blind Spot Detection Control
Module 2 - J1087- , Calibrating
Special tools and workshop equipment required
♦ Calibration Unit - VAS6350A-
♦ Vehicle Diagnostic Tester
Note
Before the actual calibration procedure for the control modules,
the Calibration Unit - VAS6350A- must be set up as described in
the chapter.
The following should not occur during the calibration procedure:
• Vehicle doors must not be opened or closed.
• People must not sit in the vehicle.
• People must not go between the vehicle and the Calibration
Tool - Lane Change Calibration Tool - VAS6350/4- .
Procedure:
– Turn on the Calibration Tool - Lane Change Calibration Tool -
VAS6350/4- at the power switch -3-.
• The green LED -1- must turn on.
Note
If the red LED -2- lights up: Check the Calibration Tool - Lane
Change Calibration Tool Calibration Tool - Lane Change Calibra‐
tion Tool - VAS6350/4- .
– Connect the Vehicle Diagnostic Tester .
– Select calibration.
– Follow the instructions in the Vehicle Diagnostic Tester dis‐
play.
Note
The vehicle in the illustration is only a basic outline.
During the program sequence, there is a prompt to switch the
Calibration Tool - Lane Change Calibration Tool - VAS6350/4-
from the left to the right side of the Calibration Tool - VAS6350- .
– Turn off the Calibration Tool - Lane Change Calibration Tool -
VAS6350/4- and remove the calibration tool.
• When installed correctly, the vehicle electrical system voltage
line must be connected at bottom left of calibration device (as
seen in direction of travel).
• Sedan dimension -a- = 606 mm (measured from the upper
edge of the calibration device to workshop floor).
• Wagon dimension -a- = 618 mm (measured from the upper
edge of the calibration device to workshop floor).
• Right adjustment dimension for Sedan = 621 mm (read on
measuring scale -1-).
• Right adjustment dimension for Wagon = 678 mm (read on
measuring scale -1-).
– Turn on the -VAS6350/4- at the power switch -3-.
• The green LED -1- must turn on.
– Follow the instructions in the Vehicle Diagnostic Tester dis‐
play.
After a successful blind spot detection calibration, switch off the
ignition and disconnect the diagnostic connector.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст