Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 545
9 - Defroster- and Air Distribution Door Actuator
❑ Removing and installing. Refer to
⇒ “7.10 Air Distribution Door Adjuster, Removing and Installing”, page 147
.
Heater, Heater Core, Auxiliary Heater Heating Element
1 - Screw
❑ 2 Nm
2 - Coolant Pipe for the Heater
Core
❑ There are different ver‐
sions. Refer to the Parts
Catalog.
❑ Coolant supply from en‐
gine
❑ Removing and instal‐
ling. Refer to
.
3 - Clamp
4 - Coolant Pipe for the Heater
Core
❑ There are different ver‐
sions. Refer to the Parts
Catalog.
❑ Coolant return to engine
❑ Removing and instal‐
ling. Refer to
.
5 - Seal
❑ There are different ver‐
sions. Refer to the Parts
Catalog.
❑ Replacing
6 - Cover
❑ For the heater core
7 - Screw
❑ 1 Nm
8 - Foam Spacer
❑ For sealing/insulating
❑ For vehicles without an A/C system, without opening for the expansion valve. Refer to the Parts Catalog.
❑ Observe installed position
9 - Bracket
❑ For the coolant pipes
10 - Foam Piece
❑ For insulating
❑ Observe installed position
11 - Heater
❑ For vehicles without an Auxiliary Heater Heating Element - Z35- with Auxiliary Air Heater Control Module
- J604- , the opening for the auxiliary heater is closed.
❑ Removing and installing. Refer to
⇒ “4.5 Heater and A/C Unit, Removing and Installing”, page 83
.
12 - Heater Core
❑ There are different versions. Refer to the Parts Catalog.
❑ Removing and installing. Refer to
⇒ “4.15 Heater Core, Removing and Installing”, page 98
13 - Auxiliary Heater Heating Element - Z35- with Auxiliary Air Heater Control Module - J604-
❑ Checking. Refer to
.
❑ Removing and installing. Refer to
14 - Screw
❑ 2 Nm
❑ Quantity: 2
15 - Wire
❑ For the Auxiliary Heater Heating Element - Z35- with Auxiliary Air Heater Control Module - J604-
16 - Ground (GND) Cable for the Auxiliary Heater Heating Element - Z35- with Auxiliary Air Heater Control
Module - J604-
❑ Nut 9 ± 1 Nm
❑ For the auxiliary heater
17 - Screw
❑ 2 Nm
❑ Quantity: 3
18 - Hose Clamp
19 - Seal
❑ There are different versions. Refer to the Parts Catalog.
❑ Replacing
Air Intake Duct, Dust and Pollen Filter, Fresh Air Blower, Door
Control
1 - Plastic Screw or Plug (de‐
pending on version)
❑ 0.3 Nm
❑ Quantity: 2
2 - Partition
❑ Removing and instal‐
ling. Refer to
3 - Fresh Air Blower Housing
and Dust and Pollen Filter
4 - Screw
❑ 1 Nm
❑ Quantity: 2
5 - Air Intake Duct
❑ Do not dismantle
❑ With fresh- and air recir‐
culation door
❑ There are different ver‐
sions. Refer to the Parts
Catalog.
❑ Removing and instal‐
ling. Refer to
6 - Not Installed
Only for vehicles with Clima‐
tronic.
7 - Not Installed
Only for vehicles with Clima‐
tronic.
8 - Recirculation Door Motor - V113-
❑ Without position sensor with end switches in the end stops. Refer to ⇒ Wiring diagrams, Troubleshooting
& Component locations.
❑ To check, use the Vehicle Diagnostic Tester in the “Guided Fault Finding” function. Refer to ⇒ Wiring
diagrams, Troubleshooting & Component locations.
❑ Removing and installing. Refer to
⇒ “7.4 Recirculation Door Motor V113 , Removing and Installing”, page 134
9 - Screw
❑ 1 Nm
❑ Quantity: 2
10 - Dust and Pollen Filter
❑ There are different versions. Refer to the Parts Catalog.
Note
On vehicles without an A/C system
and on vehicles with electric-manual
climate control system without an
activated charcoal insert from the
manufacturer.
❑ Replacement interval. Refer to ⇒ Maintenance Intervals; Rep. Gr. 03 .
❑ Removing and installing. Refer to
⇒ “4.11 Dust and Pollen Filter, Removing and Installing”, page 92
11 - Cover
❑ For dust and pollen filter
12 - Fresh Air Blower - V2-
❑ To check, use the Vehicle Diagnostic Tester in the “Guided Fault Finding” function. Refer to ⇒ Wiring
diagrams, Troubleshooting & Component locations.
❑ Removing and installing. Refer to
⇒ “4.12 Fresh Air Blower V2 , Removing and Installing”, page 95
13 - Fresh Air Blower Control Module - J126-
❑ To check, use the Vehicle Diagnostic Tester in the “Guided Fault Finding” function. Refer to ⇒ Wiring
diagrams, Troubleshooting & Component locations.
❑ Removing and installing. Refer to
⇒ “4.10 Fresh Air Blower Control Module J126 , Removing and Installing”, page 91
14 - Screw
❑ 1 Nm
❑ Quantity: 2
3.2
Fresh Air Blower - V2- , Removing and
Installing
The removal and installation is identical to vehicles with an Air
Conditioning (A/C) system. Refer to
⇒ “4.12 Fresh Air Blower V2 , Removing and Installing”,
3.3
Fresh Air Blower Control Module -
J126- , Removing and Installing
The removal and installation is identical to vehicles with an Air
Conditioning (A/C) system. Refer to
⇒ “4.10 Fresh Air Blower Control Module J126 , Removing and
.
3.4
Dust and Pollen Filter, Removing and
Installing
The removal and installation is identical to vehicles with an Air
Conditioning (A/C) system. Refer to
⇒ “4.11 Dust and Pollen Filter, Removing and Installing”,
3.5
Heater, Removing and Installing
It is not necessary to extract the refrigerant and remove the ex‐
pansion valve. The further removal and installation is identical to
vehicles with an Air Conditioning (A/C) system. Refer to
⇒ “4.5 Heater and A/C Unit, Removing and Installing”,
3.6
Heater, Disassembling and Assembling
It is not necessary to extract the refrigerant and remove the ex‐
pansion valve and the evaporator or to disassemble. The further
procedure is identical to vehicles with an Air Conditioning (A/C)
system. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст