Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 960
– Press the tabs -arrows- and remove the Central Locking -Safe-
Indicator Lamp - K133- -1- from the door trim panel.
– Release and disconnect the connector -1- from the Central
Locking -Safe- Indicator Lamp - K133- -2-.
Installing
Install in reverse order of removal.
– Perform a function test.
1.12
Left/Right Front Entry Lamp -W31- / -
W32- , Removing and Installing
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
Removal and installation for all entry lamps is performed in the
same way and is only described for one lamp.
♦ Left Front Entry Lamp - W31-
♦ Right Front Entry Lamp - W32-
♦ Left Rear Entry Lamp - W33-
♦ Right Rear Entry Lamp - W34-
Check the entry lamps using the output diagnostic test mode on
each door control module.
Caution
Risk of damaging the component surfaces.
♦ When positioning a prying tool, put commercially available
adhesive tape over the component in the visible area.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Pry out the lamp carefully using -3409- or a screwdriver.
– Disconnect the connector and remove the lamp.
Installing
Install in reverse order of removal.
1.13
Entry Lamp Bulb, Removing and Instal‐
ling
Removing
– Remove the front entry lamp. Refer to
⇒ “1.12 Left/Right Front Entry Lamp W31 / W32 , Removing
.
– Pry the diffusion lens carefully out of the housing in direction
of -arrow-.
– Remove the bulb -1- straight out of the socket.
Installing
Install in reverse order of removal.
1.14
Driver/Front Passenger Door Warning
Lamp -W30- / -W36- , Removing and In‐
stalling
The door warning lamp and the entry lamp make up one compo‐
nent. The can be remove and installed together.
– Entry Lamp, Removing and installing. Refer to
⇒ “1.12 Left/Right Front Entry Lamp W31 / W32 , Removing
.
1.15
Driver/Front Passenger Door Opener Il‐
lumination Bulb -L108- / -L109- , Re‐
moving and Installing
The removal and installation is described for the left side. Re‐
moving and installing on the right side is identical.
Caution
There is a risk of damaging the fiber-optic cable.
♦ Only touch the fiber-optic cable on the light fittings in the
area of the interior door mechanism.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the front door trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Front Door Trim Panels; Front Door Trim Panel,
Removing and Installing .
Finger Position on the Fiber-Optic Cable
1 - Fiber-optic cable
A - Index and middle fingers
B - Thumb
– Disengage the connector and disconnect.
– Disengage the fiber-optic cable on the front bracket -1- in the
direction of the arrow -A-.
– Carefully lift the fiber-optic cable -3- in the direction of the ar‐
row -B- and pivot from the interior door mechanism -4-.
– Remove the fiber-optic cable from the mount -2-.
Installing
Install in reverse order of removal.
– Perform a function test.
1.16
Left/Right Front Door Ambient Lighting
Bulb 2 - L203- / -L204- , Removing and
Installing
The Left Front Door Ambient Lighting Bulb 2 - L203- and the Right
Front Door Ambient Lighting Bulb 2 - L204- are integrated in the
door trim panel decorative strip and cannot be replaced individu‐
ally.
– Remove the front door trim panel decorative strip. Refer to ⇒
Body Interior; Rep. Gr. 70 ; Front Door Trim Panels; Overview
- Front Door Trim Panel .
1.17
Left/Right Rear Entry Lamp -W33- / -
W34- , Removing and Installing
Removal and installation for all entry lamps is performed in the
same way and is only described for one lamp.
– Entry Lamp, Removing and installing. Refer to
⇒ “1.12 Left/Right Front Entry Lamp W31 / W32 , Removing
.
1.18
Left/Right Rear Door Warning Lamp -
W37- / -W38- , Removing and Installing
The door warning lamp and the entry lamp make up one compo‐
nent. The can be remove and installed together.
– Entry Lamp, Removing and installing. Refer to
⇒ “1.12 Left/Right Front Entry Lamp W31 / W32 , Removing
.
1.19
Selector Lever Transmission Range Po‐
sition Display Unit - Y26- , Removing
and Installing
The Selector Lever Transmission Range Position Display Unit -
Y26- -1- is integrated in the selector lever boot and cannot be
replaced individually.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the selector lever boot. Refer to ⇒ Rep. Gr. 34 ;
Selector Mechanism; Selector Lever Handle, Removing and
Installing .
Installing
Install in reverse order of removal.
– Perform a function test.
1.20
Luggage Compartment Lamp - W3- ,
Removing and Installing
⇒ “1.20.1 Luggage Compartment Lamp W3 , Removing and In‐
stalling, Sedan”, page 248
⇒ “1.20.2 Luggage Compartment Lamp W3 , Removing and In‐
1.20.1
Luggage Compartment Lamp - W3- ,
Removing and Installing, Sedan
Caution
Risk of damaging the component surfaces.
♦ When positioning a prying tool, put commercially available
adhesive tape over the component in the visible area.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст