Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 959
1.6.3
Component Location Overview - Roof Trim Panel Lamps, Wagon, with
Panorama Roof
1 - Driver Vanity Mirror Lamp -
W20-
❑ Removing and instal‐
ling. Refer to
.
2 - Left Rear Interior Lamp -
W47-
❑ Removing and instal‐
ling. Refer to
.
3 - Luggage Compartment
Lamp - W3-
❑ Removing and instal‐
ling. Refer to
.
4 - Right Rear Interior Lamp -
W48-
❑ Removing and instal‐
ling. Refer to
.
5 - Front Passenger Vanity Mir‐
ror Lamp - W14-
❑ Removing and instal‐
ling. Refer to
⇒ “1.22 Driver/Front Passenger Vanity Mirror Lamp W20 / W14 , Removing and Installing”, page 250
6 - Front Interior Lamp - WX1-
❑ With Driver Reading Lamp - W19- and Front Passenger Reading Lamp - W13-
❑ Removing and installing. Refer to
⇒ “1.24 Front Interior Lamp W1 Bulb, Removing and Installing”, page 252
❑ Bulb for Front Interior Lamp - WX1- , Removing and installing. Refer to
⇒ “1.24 Front Interior Lamp W1 Bulb, Removing and Installing”, page 252
❑ Bulb for Driver Reading Lamp - W19- / Front Passenger Reading Lamp - W13- , Removing and installing.
⇒ “1.24 Front Interior Lamp W1 Bulb, Removing and Installing”, page 252
.
1.7
Glove Compartment Lamp - W6- , Re‐
moving and Installing
For a Glove Compartment Lamp - W6- the lamp must be replaced
if there is a faulty LED
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Push the retaining tab -1- with a flat-head screwdriver and pry
up the glove compartment lamp -2-.
– Disconnect the connector -3-.
Installing
Install in the reverse order of removal while paying attention to
the following:
– Insert the glove compartment lamp into the opening and en‐
gage on the opposite side.
– Perform a function test.
1.8
Bulb for Glove Compartment Lamp -
W6- , Replacing
For a Glove Compartment Lamp - W6- the lamp must be replaced
if there is a faulty LED
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the Glove Compartment Lamp - W6- . Refer to
⇒ “1.7 Glove Compartment Lamp W6 , Removing and Instal‐
.
– Pry up the heat shield -2- when necessary on both sides ar‐
rows -A-.
– Remove the heat shield -2- from the Glove Compartment
Lamp - W6- -1-.
– Remove the bulb -1- from the bulb socket -2- on the back of
the glove compartment lamp.
Installing
Install in reverse order of removal.
– Perform a function test.
1.9
Left/Right Front Footwell Lamp -K268- /
-K269- , Removing and Installing
⇒ “1.9.1 Left Front Footwell Lamp K268 , Removing and Instal‐
ling, Driver Side”, page 243
⇒ “1.9.2 Right Front Footwell Lamp K269 , Removing and Instal‐
ling, Front Passenger Side”, page 243
1.9.1
Left Front Footwell Lamp - K268- , Re‐
moving and Installing, Driver Side
For a footwell lamp the lamp must be replaced if there is a faulty
LED.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Press the retaining tab -1- in the area of the -arrow A- with a
flat-head screwdriver.
– Pry up the footwell lamp -2-.
– Disengage the connector and disconnect.
Installing
Install in reverse order of removal.
– Perform a function test.
1.9.2
Right Front Footwell Lamp - K269- , Re‐
moving and Installing, Front Passenger
Side
For a footwell lamp the lamp must be replaced if there is a faulty
LED.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Press the retaining tab -1- in the area of the -arrow A- with a
flat-head screwdriver.
– Pry up the footwell lamp -2-.
– Disengage the connector and disconnect.
Installing
Install in reverse order of removal.
– Perform a function test.
1.10
Left/Right Front Footwell Illumination
Bulb -L151- / -L152- , Removing and In‐
stalling
For a front footwell lamp the lamp must be replaced if there is a
faulty LED.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the Left/Right Front Footwell Lamp -K268- / -K269- .
Refer to
⇒ “1.9 Left/Right Front Footwell Lamp K268 / K269 , Removing
.
– Pry up the heat shield -2- when necessary on both sides ar‐
rows -A-.
– Remove the heat shield -2- from the footwell lamp -1-.
– Remove the bulb -1- from the bulb socket -2- on the back of
the glove compartment lamp.
Installing
Install in reverse order of removal.
– Perform a function test.
1.11
Central Locking -Safe- Indicator Lamp -
K133- , Removing and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the front door trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Front Door Trim Panels; Front Door Trim Panel,
Removing and Installing .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст