Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 429
– Drill out the rivets -2- from the backrest frame.
– Remove the backrest release bearing -3- from the backrest
frame.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “2.4 Overview - Front Backrest”, page 323
♦ Refer to
⇒ “2.2 Overview - Front Seat”, page 318
2.29
Backrest Release Cable, Removing and
Installing
Note
The left and right release cables cannot be replaced separately.
Special tools and workshop equipment required
♦ Pop Rivet Pliers - VAG1753B-
♦ Drill
♦ Protective Eyewear
Removing
– Remove the backrest cover with the backrest cushion. Refer
to
⇒ “1.5 Backrest Cover and Cushion, Removing and Installing”,
Note
The spring mat or lumbar support does not need to be removed
when removing and installing the release cables.
– Using pliers, disengage the eyelet -3- from the pins -4- for the
backrest release on both sides.
WARNING
Danger of eye injury.
♦ Wear protective eyewear.
– Remove the left and right rivet -2- and remove the bracket
-1- from the backrest frame -5-.
– Pry the release cable -1- from the backrest release bearing
-2- with a screwdriver in the direction of the -arrow-.
– Unclip the bracket -1- from the backrest frame -2-.
– Guide out the end of the release cable through the mount
opening in the backrest frame.
– Separate the cable tie and remove the release cables from the
backrest frame.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “2.4 Overview - Front Backrest”, page 323
♦ Refer to
⇒ “2.2 Overview - Front Seat”, page 318
2.30
Backrest Release Cable, Adjusting
WARNING
Make sure the backrest is locked (zero position), otherwise it
could tip forward accidentally.
– Remove the backrest cover with the backrest cushion. Refer
to
⇒ “1.5 Backrest Cover and Cushion, Removing and Installing”,
The following prerequisites must be met to adjust:
• Backrest release -2- to the lower stop (backrest locks).
– Pivot the backrest release bearing -1- upward until a distance
of -a- = 2 to 4 mm is between the backrest frame stop surface
-arrow A- and the bearing stop -arrow B-.
– Secure the backrest release bearing in this position, using for
example an angled metal rod.
– Adjust the release cables on both release cable adjusters
-1 and 2-.
– To adjust, turn the upper section -3- and the lower section
-4- contrary to each other.
– Adjust the cable so it is free of play and tension.
Note
♦
The illustration only shows one side of the retainer.
♦
When adjusting cables -1-, they must not be tensioned at the
backrest release -2-.
– After adjusting release cables, perform a functionality test of
the backrest release.
– If it does not release or only releases partially, check the re‐
lease cable routing or repeat the adjustment.
2.31
Entry Assistance Release Cable A, Re‐
moving and Installing
Removing
– Remove the front seat. Refer to
⇒ “2.10 Front Seat, Removing and Installing”, page 335
.
– Attach the front seat to the Fixture For Seat Repair . Refer to
⇒ “1.2 Front Seat, Mounting on Fixture for Seat Repair”, page
– Move the front seat into its highest position.
– Remove the tunnel side seat trim. Refer to
⇒ “2.13 Tunnel-Side Seat Trim, Removing and Installing”,
.
– Turn the backrest adjustment hand wheel forward until stop.
– Unclip the release cable A bracket -1- from the backrest.
– Disengage the release cable A -2- from the lever on the back‐
rest hinge.
– Disengage the cable A bracket -1- for entry assistance from
the bracket on the seat pan.
– Unclip the bracket -2- for the release cable from the seat pan.
– Disengage the release cable A from the seat longitudinal ad‐
juster -arrow- and remove.
Installing
Install in reverse order of removal while paying attention to the
following:
– Adjust the release cable A. Refer to
⇒ “2.32 Entry Assistance Release Cable A, Adjusting”,
.
Tightening Specifications
♦ Refer to
⇒ “2.2 Overview - Front Seat”, page 318
2.32
Entry Assistance Release Cable A, Ad‐
justing
Special tools and workshop equipment required
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст