Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 251
9 - Operating Cable with Button
❑ Component location: bolted into the rear lid
❑ Removing and installing. Refer to
⇒ “2.7 Actuator, Removing and Installing”, page 60
.
10 - Rear Lid Latch
❑ Component location: bolted to the rear lid
❑ Removing and installing. Refer to
⇒ “2.6 Latch, Removing and Installing”, page 58
11 - Left Rear Lid Connector Station
❑ Component location: behind the D-pillar trim panel
❑ Removing and installing. Refer to ⇒ Body Interior; Rep. Gr. 70 ; Passenger Compartment Trim; D-Pillar
Trim Panel, Removing and Installing .
12 - Left Rear Door Lock
❑ The door lock is attached to the door inner panel
❑ The power central locking system is integrated in the door lock
❑ Removing and installing. Refer to
⇒ “2.13 Door Lock, Removing and Installing”, page 179
.
13 - Driver Side Rear Window Regulator Motor Control Module - J1016-
❑ Removing and installing. Refer to
⇒ “3.3 Driver Side Rear Window Regulator Motor Control Module J1016 and Front Passenger Side Rear
Window Regulator Motor Control Module J1017 , Removing and Installing”, page 137
14 - Connector Station
❑ Component location: left B-pillar
❑ Loosen the boot on the pillar to disconnect the connector
15 - Left Front Door Lock
❑ The door lock is attached to the door inner panel
❑ The power central locking system is integrated in the door lock
❑ Removing and installing. Refer to
⇒ “2.13 Door Lock, Removing and Installing”, page 119
.
16 - Driver Door Control Module - J386-
❑ Installed separately from the window regulator motor in the door.
❑ Removing and installing. Refer to
⇒ “3.2 Driver Door Control Module J386 and Front Passenger Door Control Module J387 , Removing
17 - Window Regulator Central Switch
❑ Component location: installed in the door trim panel
❑ Removing and installing. Refer to ⇒ Electrical Equipment; Rep. Gr. 96 ; Controls; Component Location
Overview - Controls in Front Doors .
18 - Central Locking Button
❑ Component location: installed in the door trim panel
❑ Removing and installing. Refer to ⇒ Electrical Equipment; Rep. Gr. 96 ; Controls; Component Location
Overview - Controls in Front Doors .
19 - Connector Station
❑ Component location: left A-pillar
❑ Loosen the boot on the pillar to disconnect the connector
20 - Alarm Horn - H12-
❑ Removing and installing. Refer to ⇒ Electrical Equipment; Rep. Gr. 96 ; Anti-theft Alarm System; Alarm
Horn H12, Removing and Installing .
21 - Engine Hood Contact Switch - F266-
❑ Contact switch for anti-theft alarm system
❑ Component location: on the latch
❑ Removing and installing. Refer to
3.2
Driver Door Control Module - J386- and
Front Passenger Door Control Module -
J387- , Removing and Installing
Removing
– Remove the front door trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Front Door Trim Panels; Front Door Trim Panel,
Removing and Installing .
– Release and disconnect all existing connectors on the door
control module -1-.
– Release the tabs -2- in the direction of -arrow- and remove
door control module -1- from the inner door panel.
Installing
Install in reverse order of removal while paying attention to the
following:
– Perform a function test before installing the front door trim
panel.
3.3
Driver Side Rear Window Regulator Mo‐
tor Control Module - J1016- and Front
Passenger Side Rear Window Regula‐
tor Motor Control Module - J1017- , Re‐
moving and Installing
The procedure for removing and installing the Driver Side Rear
Window Regulator Motor Control Module - J1016- / Front Pas‐
senger Side Rear Window Regulator Motor Control Module -
J1017- follows the procedure for removing and installing the rear
window regulator motor. Refer to
⇒ “2.4 Window Regulator Motor, Removing and Installing”,
3.4
Key Battery, Removing and Installing
Removing
– Fold out the key blade -1- in direction of -arrow a-.
– Using a small screwdriver -3-, lift up the battery compartment
cover -2- in direction of -arrow b-.
– Using a small screwdriver -3-, lift up the battery -1- from the
battery compartment -2- in direction of -arrow-.
Installing
Note
♦
Before installing the battery, one of the buttons must be push‐
ed.
♦
This resets the radio-frequency unit, and it can now recognize
the new battery.
Note the polarity and installation position when installing the bat‐
tery. The positive terminal is marked.
– Insert the battery -1- by pressing it lightly in direction of
-arrow a- into the battery compartment -2-.
– Push the battery compartment cover -3- and the radio-fre‐
quency unit together in direction of -arrow b-.
– The ignition key must now be synchronized. Refer to
.
Ignition Key, Synchronizing
– Remove the lock cylinder cap -3-. Refer to
⇒ “2.8 Lock Cylinder Cap, Removing and Installing”,
.
– Hold the ignition key -2- at the lock cylinder -1- and push the
“open” button.
– Unlock the vehicle using the ignition key -2- within one minute
via the lock cylinder -1-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст