Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 409
– Pull the luggage compartment cover -1- out of the left luggage
compartment side trim panel and remove it.
Installing
Install in reverse order of removal.
6.8
Lock Carrier Trim Panel, Removing and
Installing
Special tools and workshop equipment required
♦ Pry Lever - 80-200-
Removing
Vehicles with Trailer Hitch, Sedan
– Remove the luggage compartment floor toward the rear.
– Release the clip -2- from the cable bracket -1-.
– Remove the cable bracket -1- upward from the cable -3-.
Vehicles with Trailer Hitch, Wagon
– Release the mount on the left and right side on the luggage
compartment floor by it turning 90° and remove the luggage
compartment floor toward the rear out of the vehicle.
– Release the clip -1- from the release cable lever -2- and move
it upward in direction of -arrow A-.
– Remove the release cable lever -2- forward from the release
cable -3- in direction of -arrow B-.
Continuation for All Vehicles
– Remove the rear lid seal -2- near the lock carrier trim panel
-1-.
– Loosen the lock carrier trim panel -1- near the clips from the
body mounts using the Pry Lever - 80-200- -arrows-.
Vehicles with Trailer Hitch
– Disconnect the connector from the Trailer Hitch -Locked- In‐
dicator Lamp - K226- .
Continuation for All Vehicles
– Remove the lock carrier trim panel -1- upward.
Installing
Note
♦
Check all the fasteners for damage and replace if necessary.
♦
Remove any remaining clips in the body mounting points using
the Omega Clip Tool - T40280- . To install, insert into the lock
carrier trim panel.
♦
Make sure the lock carrier trim panel is inside the rear lid seal
molding after it is installed.
Install in reverse order of removal.
6.9
Rear Shelf Compartment, Removing
and Installing
Note
The following describes the removing and installing on the left
side of the vehicle. Removing and installing on the right side is
identical.
Special tools and workshop equipment required
♦ Pry Lever - 80-200-
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
4-Door
– Remove the wheel housing trim panel. Refer to
⇒ “5.17 Wheel Housing Trim Panel, Removing and Installing”,
.
2-Door
– Remove the side trim panel. Refer to
⇒ “5.16 Side Trim Panel, Removing and Installing”,
.
Continuation for All Vehicles
– Remove the lock carrier trim panel. Refer to
⇒ “6.8 Lock Carrier Trim Panel, Removing and Installing”,
.
– Remove the bolts -3 and 5-.
– Remove the spreader plug -2-.
– Loosen the rear shelf compartment -1- near the clips -4- from
the body mounts using the Pry Lever - 80-200- .
– If equipped, disconnect the connectors and remove the rear
shelf compartment -1-.
Installing
Note
♦
Check all the fasteners for damage and replace if necessary.
♦
Remove any remaining clips in the body mounting points using
the Omega Clip Tool - T40280- . To install, insert into the rear
shelf compartment.
♦
Make sure the rear shelf compartment is inside the rear lid seal
molding after it is installed.
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “6.2 Overview - Rear Shelf Compartment”, page 277
6.10
Tie Down, Removing and Installing
Note
The following describes the removing and installing on the left
side of the vehicle. Removing and installing on the right side is
identical.
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Open the bracket -4- and open the cover -1- using a screw‐
driver.
– Remove the bolt -3- and the tie-down -2-.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “6.3 Overview - Luggage Compartment Side Trim Panel”,
6.11
Luggage Compartment Floor Covering
Bracket, Removing and Installing
⇒ “6.11.1 Luggage Compartment Floor Covering Bracket, Re‐
moving and Installing, Sedan”, page 287
⇒ “6.11.2 Luggage Compartment Floor Covering Bracket, Re‐
moving and Installing, Wagon”, page 288
6.11.1
Luggage Compartment Floor Covering
Bracket, Removing and Installing, Se‐
dan
Note
The following describes the removing and installing on the left
side of the vehicle. Removing and installing on the right side is
identical.
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Fold the rear seat backrests forward.
– Remove the luggage compartment floor toward the rear.
– Remove the bolts -2-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст