Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 410
– Remove the luggage compartment floor covering bracket -1-.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “6.4 Overview - Luggage Compartment Floor”, page 280
6.11.2
Luggage Compartment Floor Covering
Bracket, Removing and Installing, Wag‐
on
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Fold the rear seat backrests forward.
– Release the mount on the left and right side on the luggage
compartment floor by it turning 90° and remove the luggage
compartment floor toward the rear out of the vehicle.
– Remove the luggage compartment floor support upward
.
– Pull the sidewall -3- upward out of the left and right luggage
compartment side trim panels and remove it.
– Turn the installation bracket -1- on the left and right side 90°
counter-clockwise and remove upward.
– Remove the luggage compartment floor trim -2- on the left and
right side upward.
– Unclip the center luggage compartment floor trim -1- upward
from the carrier -3-.
– Remove the bolts -2-.
– Remove the support -3- for the center luggage compartment
liner -1- toward the rear.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “6.4.2 Overview - Luggage Compartment Floor, Wagon”,
6.12
Luggage Compartment Side Trim Pan‐
el, Removing and Installing
⇒ “6.12.1 Luggage Compartment Side Trim Panel, Removing and
Installing, Sedan”, page 289
⇒ “6.12.2 Luggage Compartment Side Trim Panel, Removing and
6.12.1
Luggage Compartment Side Trim Pan‐
el, Removing and Installing, Sedan
Note
The following describes the removing and installing on the left
side of the vehicle. Removing and installing on the right side is
identical.
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
♦ Pry Lever - 80-200-
Removing
– Remove the rear seat backrest. Refer to
⇒ “3.8 Rear Seat Backrest, Removing and Installing”,
.
– Remove the rear shelf compartment. Refer to
⇒ “6.9 Rear Shelf Compartment, Removing and Installing”,
.
– If equipped, remove the luggage compartment floor covering
bracket. Refer to
⇒ “6.11.1 Luggage Compartment Floor Covering Bracket, Re‐
moving and Installing, Sedan”, page 287
.
– Remove the tie-down -2-. Refer to
⇒ “6.10 Tie Down, Removing and Installing”, page 287
– Remove the clips -4-.
– Disengage and remove the luggage compartment side trim
panel -1-.
Installing
Note
♦
Check all the fasteners for damage and replace if necessary.
♦
Make sure the luggage compartment side trim panel fits inside
the rear lid seal molding after it is installed.
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
6.12.2
Luggage Compartment Side Trim Pan‐
el, Removing and Installing, Wagon
Note
The following describes the removing and installing on the left
side of the vehicle. Removing and installing on the right side is
identical.
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
♦ Pry Lever - 80-200-
Removing
– Remove the luggage compartment cover. Refer to
⇒ “6.7 Luggage Compartment Cover, Removing and Instal‐
– Remove the rear seat backrest. Refer to
⇒ “3.8 Rear Seat Backrest, Removing and Installing”,
.
Vehicles with Side Cushion
– Remove the side cushion. Refer to
⇒ “3.16 Side Cushion, Removing and Installing”, page 391
.
Vehicles without Side Cushion
– Remove the wheel housing trim panel. Refer to
⇒ “5.17.2 Wheel Housing Trim Panel, Removing and Instal‐
Continuation for All Vehicles
– Remove the D-pillar trim panel. Refer to
⇒ “5.15 D-Pillar Trim Panel, Removing and Installing”,
.
– Remove the lock carrier trim panel. Refer to
⇒ “6.8 Lock Carrier Trim Panel, Removing and Installing”,
.
– Remove the tie-down -7-. Refer to
⇒ “6.10 Tie Down, Removing and Installing”, page 287
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст