Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 776
4
Sensors
⇒ “4.1 Overview - Front Axle Speed Sensor”, page 35
⇒ “4.2 Overview - Rear Axle Speed Sensor”, page 36
⇒ “4.3 Right/Left Front ABS Wheel Speed Sensor G45 / G47 ,
Removing and Installing”, page 37
⇒ “4.4 Right/Left Rear ABS Wheel Speed Sensor G44 / G46 ,
Removing and Installing”, page 38
⇒ “4.5 ESP Sensor Unit G419 , Removing and Installing”,
page 39
⇒ “4.6 Steering Angle Sensor G85 , Removing and Installing”,
page 39
⇒ “4.7 ABS Sensor Ring, Checking”, page 39
4.1
Overview - Front Axle Speed Sensor
1 - Wheel Speed Sensor -
G47- / -G45-
❑ Left Front ABS Wheel
Speed Sensor - G47- /
Right Front ABS Wheel
Speed Sensor - G45-
❑ Removing and instal‐
ling. Refer to
❑ Clean the inner surface
of the opening before in‐
serting the sensor
❑ Coat the hole with Hot
Bolt Paste - G 052 112
A3- .
2 - Bolt
❑ 8 Nm
3 - Drive Axle
❑ Overview. Refer to ⇒
Suspension, Wheels,
Steering; Rep. Gr. 40 ;
Drive Axle; Overview -
Drive Axle .
❑ Removing and instal‐
ling. Refer to ⇒ Suspen‐
sion, Wheels, Steering;
Rep. Gr. 40 ; Drive Axle;
Drive Axle, Removing
and Installing .
4 - Wheel Hub with Wheel
Bearing Unit
❑ The ABS sensor ring is
integrated in the wheel bearing unit
❑ Removing and installing. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 40 ; Wheel Bearing; Wheel
Bearing Unit, Removing and Installing .
4.2
Overview - Rear Axle Speed Sensor
⇒ “4.2.1 Overview - Rear Axle Speed Sensor, FWD”, page 36
⇒ “4.2.2 Overview - Rear Axle Speed Sensor, AWD”, page 37
4.2.1
Overview - Rear Axle Speed Sensor, FWD
1 - ABS Speed Sensor
❑ Removing and Instal‐
ling. Refer to
❑ Clean the inner surface
of the hole before insert‐
ing the sensor
❑ Coat the hole with Hot
Bolt Paste - G 052 112
A3- .
2 - Bolt
❑ 8 Nm
3 - Wheel Hub with Wheel
Bearing Unit
❑ The ABS sensor ring is
integrated in the wheel
bearing unit
4.2.2
Overview - Rear Axle Speed Sensor, AWD
1 - ABS Speed Sensor
❑ Clean the inner surface
of the hole before insert‐
ing the sensor
❑ Coat the inner surface
with Hot Bolt Paste -
G 052 112 A3- .
❑ Removing and Installing
2 - Bolt
❑ 8 Nm
3 - Driveshaft
❑ Overview. Refer to ⇒
Suspension, Wheels,
Steering; Rep. Gr. 42 ;
Overview - Driveshaft .
❑ Removing and instal‐
ling. Refer to ⇒ Suspen‐
sion, Wheels, Steering;
Rep. Gr. 42 ; Driveshaft;
Driveshaft, Removing
and Installing .
4 - Wheel Hub with Wheel
Bearing Unit
❑ The ABS sensor ring is
integrated in the wheel
bearing unit
❑ Check the ABS sensor
ring. Refer to
.
❑ Removing and Instal‐
ling. Refer to ⇒ Suspen‐
sion, Wheels, Steering;
Rep. Gr. 42 ; Wheel
Bearing, Trailing Arm;
Wheel Bearing Unit, Removing and Installing .
4.3
Right/Left Front ABS Wheel Speed Sen‐
sor -G45- / -G47- , Removing and In‐
stalling
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
Note
The example describes the removal and installation of the left
front ABS wheel speed sensor. The removal and installation of
the right front ABS wheel speed sensor is identical.
Removing
– Raise the vehicle.
– Disconnect the connector -3- from the wheel speed sensor
-1-.
– Remove the bolt -2- and pull the wheel speed sensor -1- from
the wheel bearing housing.
Installing
Install in reverse order of removal. Note the following:
– Clean the inner surface of the opening before inserting the
sensor
– Coat the hole with Hot Bolt Paste - G 052 112 A3- .
Tightening Specification
♦ Refer to
⇒ “4.1 Overview - Front Axle Speed Sensor”, page 35
4.4
Right/Left Rear ABS Wheel Speed Sen‐
sor -G44- / -G46- , Removing and In‐
stalling
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
Note
The example describes the removal and installation of the left rear
ABS wheel speed sensor. The removal and installation of the right
rear ABS wheel speed sensor is identical.
Wheel Speed Sensor -1-
Removing
– Raise the vehicle.
– Disconnect the connector -2- from the wheel speed sensor.
– Remove bolt -1-, and remove the wheel speed sensor from the
wheel bearing housing.
Installing
Install in reverse order of removal. Note the following:
– Clean the inner surface of the opening before inserting the
sensor
– Coat the hole with Hot Bolt Paste - G 052 112 A3- .
Tightening Specification
♦ Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст