Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 394
Removing
– Remove the glove compartment. Refer to
⇒ “1.17 Glove Compartment, Removing and Installing”,
.
– Remove the spreader plug -2-.
– Pull the front passenger side impact absorber -1- out of the
instrument panel in direction of -arrow- and remove it.
Installing
Install in reverse order of removal.
4
Instrument Panel Central Tube
⇒ “4.1 Overview - Instrument Panel Central Tube”, page 225
⇒ “4.2 Overview - Driver Side Impact Absorber”, page 227
⇒ “4.3 Crash Bolster, Removing and Installing”, page 228
⇒ “4.4 Instrument Panel Central Tube, Removing and Installing”,
page 229
⇒ “4.5 Driver Side Impact Absorber, Removing and Installing”,
4.1
Overview - Instrument Panel Central Tube
Note
It may be helpful to make drawings or take photos of any wires that are going to be loosened, removed and
then installed. This assures the wires will be reconnected correctly.
1 - Bracket
❑ Welded to the body
2 - Threaded Pin
❑ 20 Nm
❑ Quantity: 2
3 - Screw
❑ 20 Nm
4 - Central Tube
❑ For the instrument panel
❑ Removing and instal‐
ling. Refer to
Caution
If the central tube is to be
replaced with a new part,
malfunctions due to faul‐
ty ground connections
cannot be ruled out.
♦
The ground connections
must be free of paint,
coating, and corrosion so
that an error-free ground
connection is guaran‐
teed.
♦
Mounting threads and
contact surfaces be‐
tween the central tube
and securing brackets
must also be free of paint,
coating, and corrosion.
The threaded connec‐
tions serve as the ground
connection for the knee
airbag.
♦
The contact surfaces for
the left and right tunnel
support must be free of
paint on both sides.
These serve as the main
ground path.
5 - Nut
❑ 20 Nm
❑ Quantity: 2
Caution
There is a risk of mal‐
functions do to a faulty
ground connection.
♦
The contact surface must
be free of paint, coating,
and corrosion, the threa‐
ded connection serves
as the ground connection
for the knee airbag.
6 - Screw
❑ 4 Nm
❑ Quantity: 3
❑ If one of the screws is overtightened when installing the heater and A/C unit, use the Screw - N.
911.981.01- as a replacement.
7 - Screw
❑ 20 Nm
❑ Quantity: 2
8 - Screw
❑ 20 Nm
9 - Crash Bolster
❑ Allocation. Refer to the Parts Catalog.
❑ Removing and installing. Refer to
⇒ “4.3 Crash Bolster, Removing and Installing”, page 228
.
10 - Screw
❑ 20 Nm
❑ Driver side only
Caution
There is a risk of mal‐
functions do to a faulty
ground connection.
♦
The counter threaded
and contact surface must
be free of paint, coating,
and corrosion, the threa‐
ded connection serves
as the ground connection
for the knee airbag.
4.2
Overview - Driver Side Impact Absorber
1 - Left Driver Side Impact Ab‐
sorber
❑ Removing and instal‐
ling. Refer to
2 - Spreader Plug
❑ Replace damaged or
deformed spreader plug
3 - Screw
❑ 4.5 Nm
❑ Quantity: 2
❑ Also screws for Vehicle
Electrical System Con‐
trol Module - J519-
bracket
4 - Bracket
❑ Removing
– Remove the right driver
side impact absorber.
Refer to
– Remove the screws -5-.
– Disengage the bracket
on the central tube and
remove.
❑ Installing
Install in reverse order of
removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст