Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 50
– Remove the Steering Column Electronics Control Module -
J527- -2- from the Steering Column Combination Switch -
E595- .
Installing
Install in the reverse order of removal while paying attention to
the following:
– Before sliding the Steering Column Electronics Control Mod‐
ule - J527- -3- the following must be checked.
♦ The “arrows” -1- must align.
♦ The spiral spring -2- must be seen in the window between the
“arrows” -4-.
– Make sure that all connectors are installed securely.
Tightening Specifications
♦ Refer to
⇒ “8.1 Overview - Steering Column Switch Module”,
8.6.2
Steering Column Electronics Control
Module - J527- , Removing and Instal‐
ling, Valeo
The Airbag Spiral Spring/Return Spring with Slip Ring - F138- is
integrated into the Steering Column Electronics Control Module -
J527- .
If the control module is being replaced, use the Vehicle Diagnostic
Tester and select the “Replacing” function for the respective con‐
trol module in “Guided Fault Finding”.
Removing
– Position the front wheels straight-ahead. The steering wheel
is located in the neutral position.
– Position the steering wheel as far back as possible. Use the
entire adjustment range of the steering column adjustment for
this.
– Remove the steering wheel. Refer to ⇒ Suspension, Wheels,
Steering; Rep. Gr. 48 ; Steering Wheel; Steering Wheel, Re‐
moving and Installing .
– Remove the lower steering column trim panel. Refer to ⇒ Body
Interior; Rep. Gr. 68 ; Storage Compartments and Covers;
Lower Steering Column Trim Panel, Removing and Installing .
WARNING
Risk of destroying electronic components with static discharge.
♦ Before disconnecting the connector, discharge static elec‐
tricity from your body by touching a grounded vehicle
component such as the door striker pin.
– Push the connector lock in the direction of the -arrow A- and
disconnect the connector -1-.
– Push the connector lock in the direction of the -arrow B- and
disconnect the connector -2-.
– Push the connector lock in the direction of the -arrow C- and
disconnect the connector -3-.
– Remove the connector lock in the direction of the -arrow D-
and press down.
– Disconnect the connector -4-.
– Push the connector lock in the direction of the -arrow E- and
disconnect the connector -5-.
– Remove the connector lock in the direction of the -arrow F-
and press down.
– Disconnect the connector -6-.
– Remove the screws -1-.
– Remove the Steering Column Electronics Control Module -
J527- -2- from the Steering Column Combination Switch -
E595- .
Installing
Install in the reverse order of removal while paying attention to
the following:
– Before sliding the Steering Column Electronics Control Mod‐
ule - J527- -3- the following must be checked.
♦ The “arrows” -1- must align.
♦ The spiral spring -2- must be seen in the window between the
“arrows” -4-.
– Make sure that all connectors are installed securely.
Tightening Specifications
♦ Refer to
⇒ “8.1 Overview - Steering Column Switch Module”,
8.7
Turn Signal Switch - E2- , Removing and
Installing
⇒ “8.7.1 Turn Signal Switch E2 , Removing and Installing, Kostal”,
page 192
⇒ “8.7.2 Turn Signal Switch E2 , Removing and Installing, Valeo”,
8.7.1
Turn Signal Switch - E2- , Removing and
Installing, Kostal
Turn Signal Switch - E2- , Cruise Control Switch - E45- and the
Windshield Wiper Intermittent Mode Switch - E22- together make
up the Steering Column Combination Switch - E595- .
The switch cannot be separated. If an individual switch is faulty
the Steering Column Combination Switch - E595- must be re‐
placed.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the Steering Column Electronics Control Module -
J527- . Refer to
⇒ “8.6 Steering Column Electronics Control Module J527 ,
Removing and Installing”, page 187
.
– Remove the bolt -2- on the bottom.
– Remove the Steering Column Combination Switch - E595-
-1-.
Installing
Install in reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст