Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 51
8.7.2
Turn Signal Switch - E2- , Removing and
Installing, Valeo
Turn Signal Switch - E2- , Cruise Control Switch - E45- and the
Windshield Wiper Intermittent Mode Switch - E22- together make
up the Steering Column Combination Switch - E595- .
The switch cannot be separated. If an individual switch is faulty
the Steering Column Combination Switch - E595- must be re‐
placed.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the Steering Column Electronics Control Module -
J527- . Refer to
⇒ “8.6 Steering Column Electronics Control Module J527 ,
Removing and Installing”, page 187
– Push the release -1- on both sides in the direction of the
-arrow A-.
– Slightly remove the Steering Column Combination Switch -
E595- -2-.
– Push the release -3- in the direction of the -arrow B-.
– Remove the Steering Column Combination Switch - E595-
-2-.
Installing
Install in reverse order of removal.
8.8
Cruise Control Switch - E45- , Removing
and Installing
Turn Signal Switch - E2- , Cruise Control Switch - E45- and the
Windshield Wiper Intermittent Mode Switch - E22- together make
up the Steering Column Combination Switch - E595- .
The switch cannot be separated. If an individual switch is faulty
the Steering Column Combination Switch - E595- must be re‐
placed.
– Turn Signal Switch - E2- , Removing and installing. Refer to
⇒ “8.7 Turn Signal Switch E2 , Removing and Installing”, page
.
8.9
Windshield Wiper Intermittent Mode
Switch - E22- , Removing and Installing
Turn Signal Switch - E2- , Cruise Control Switch - E45- and the
Windshield Wiper Intermittent Mode Switch - E22- together make
up the Steering Column Combination Switch - E595- .
The switch cannot be separated. If an individual switch is faulty
the Steering Column Combination Switch - E595- must be re‐
placed.
– Turn Signal Switch - E2- , Removing and installing. Refer to
⇒ “8.7 Turn Signal Switch E2 , Removing and Installing”, page
.
8.10
Anti-Theft Immobilizer Reader Coil -
D2- , Removing and Installing
⇒ “8.10.1 Anti-Theft Immobilizer Reader Coil D2 , Removing and
Installing, Vehicles with Keyless Access”, page 194
8.10.1
Anti-Theft Immobilizer Reader Coil -
D2- , Removing and Installing, Vehicles
with Ignition Key
The Anti-Theft Immobilizer Reader Coil - D2- is integrated in the
lock cylinder and cannot be replaced separately.
– Lock cylinder, removing and installing. Refer to
⇒ “8.2 Lock Cylinder, Removing and Installing”, page 179
.
8.10.2
Anti-Theft Immobilizer Reader Coil -
D2- , Removing and Installing, Vehicles
with Keyless Access
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Position the steering wheel as far back as possible. Use the
entire adjustment range of the steering column adjustment for
this.
– Remove the lower steering column trim panel. Refer to ⇒ Body
Interior; Rep. Gr. 68 ; Storage Compartments and Covers;
Lower Steering Column Trim Panel, Removing and Installing .
– Remove the Anti-Theft Immobilizer Reader Coil - D2- -2- in the
direction of the -arrow A- from the mount -1-.
Installing
Install in the reverse order of removal while paying attention to
the following:
– Push in the Anti-Theft Immobilizer Reader Coil - D2- until it
engages audibly in the mount.
8.11
Steering Lock Housing, Removing and
Installing
Special tools and workshop equipment required
♦ 7/16 Inch Extractor - T10424US-
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the steering column switch module. Refer to
⇒ “8.5 Steering Column Switch Module, Removing and Instal‐
– Disconnect the connectors -1 and 4-.
If the shear bolt cannot be removed using the -T10424US- , use
an angled hand drill and 8.5 mm diameter bit to drill it out.
– Remove the shear bolt -2- using the -T10424US- .
– Remove the steering lock housing -3-.
To replace the steering lock housing, the Ignition/Starter Switch -
D- and lock cylinder must be removed.
– Remove the Ignition/Starter Switch - D- . Refer to
⇒ “8.4 Ignition/Starter Switch, Removing and Installing”, page
– Remove lock cylinder. Refer to
⇒ “8.2 Lock Cylinder, Removing and Installing”, page 179
Installing
Install in the reverse order of removal while paying attention to
the following:
– Tighten the new bolts -arrows- until the head shears off.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст