Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 56
12
Trailer Hitch
⇒ “12.1 Overview - Trailer Hitch Socket”, page 213
⇒ “12.2 Trailer Socket U10 ”, page 214
⇒ “12.3 Towing Recognition Control Module J345 , Removing
12.1
Overview - Trailer Hitch Socket
⇒ “12.1.1 Overview - Trailer Hitch Socket, Sedan”, page 213
⇒ “12.1.2 Overview - Trailer Hitch Socket, Wagon”, page 214
12.1.1
Overview - Trailer Hitch Socket, Sedan
1 - Towing Recognition Control
Module - J345-
❑ Removing and instal‐
ling. Refer to
.
2 - Frame
❑ For Towing Recognition
Control Module - J345-
3 - Trailer Socket - U10-
❑ Connector assignment.
Refer to
.
12.1.2
Overview - Trailer Hitch Socket, Wagon
1 - Trailer Socket - U10-
❑ Connector assignment.
Refer to
2 - Bolt
❑ 9 Nm
3 - Towing Recognition Control
Module - J345-
❑ Removing and instal‐
ling. Refer to
4 - Control Module Bracket
❑ For Towing Recognition
Control Module - J345-
❑ Removing and instal‐
ling. Refer to
5 - Vehicle Tools Bracket
12.2
Trailer Socket - U10-
Characteristics of pin 9.
♦ Pin 9, continuous positive, supplies the trailer with positive
from the Battery - A- .
♦ The continuous positive is always connected directly with the
Battery - A- .
♦ Only low current is permitted, approximately 7.5 - 10 A.
Trailer Socket - U10- Connector Assignment.
The exact connector assignment can be found the applicable wir‐
ing diagram. Refer to ⇒ Wiring diagrams, Troubleshooting &
Component locations.
12.3
Towing Recognition Control Module -
J345- , Removing and Installing
⇒ “12.3.1 Towing Recognition Control Module J345 , Removing
and Installing, Sedan”, page 215
⇒ “12.3.2 Towing Recognition Control Module J345 , Removing
and Installing, Wagon”, page 215
12.3.1
Towing Recognition Control Module -
J345- , Removing and Installing, Sedan
If the control module is being replaced, use the Vehicle Diagnostic
Tester and select the “Replacing” function for the respective con‐
trol module in “Guided Fault Finding”.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the luggage compartment left trim panel. Refer to ⇒
Body Interior; Rep. Gr. 70 ; Luggage Compartment Trim Pan‐
els; Luggage Compartment Side Trim Panel, Removing and
Installing .
– Push the clips -1- together in the direction of the -arrows A-.
– Remove the Towing Recognition Control Module - J345- -3-.
– Disconnect the connectors -2-.
Installing
Install in reverse order of removal.
12.3.2
Towing Recognition Control Module -
J345- , Removing and Installing, Wagon
If the control module is being replaced, use the Vehicle Diagnostic
Tester and select the “Replacing” function for the respective con‐
trol module in “Guided Fault Finding”.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the lid in the left luggage compartment side trim pan‐
el.
– Remove the vehicle tool kit.
– Remove the screws -1-.
– Pull the vehicle tools bracket in the direction of -arrow A-.
– Disconnect the connectors -2-.
– Remove the vehicle tools bracket in the direction of
-arrow B- from the side panel.
– Push the catch -1- in the direction of the -arrow A-.
– Lift up the Towing Recognition Control Module - J345- -2- and
remove in the direction of the arrow -B-.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст