Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 788
– Press the lever -2- located on the brake caliper in the direction
of the -arrow- and disengage the brake cable -1-.
– Squeeze the tabs -3- and remove the brake cable from the
bracket -4- on the brake caliper.
– Remove the center console. Refer to ⇒ Body Interior; Rep.
Gr. 68 ; Center Console; Overview - Center Console .
– Loosen the adjusting nut -1- until it is possible to disengage
the parking brake cable -2- from the compensator bracket
-3-.
– Pull the brake cable -1- out of the retainer -arrow A- on the
bracket -2-.
– Pull the brake cable -1- in the direction of the -arrow- out of the
guide -arrow B- on the bracket -2-.
– Disengage the brake cable -1- from the bracket -3- and pull it
from the guide tube -2-.
Installing
Install in reverse order of removal. Note the following:
– Pay attention that the guide tube and the seal are seated cor‐
rectly.
– Push the brake cable -1- in the guide tube -2- until stop.
– Engage the brake cable -1- in the bracket -3- and push in wire.
– Engage the brake cable at the marking -arrow-.
– Insert the brake cable -1- into the guide -arrow B- on the
bracket -2- opposite the direction of -arrow-.
– Clip the brake cable -1- back into the retainer -arrow A- on the
bracket -2-.
– Push the brake cable -1- through the bracket -4- on the brake
caliper until both tabs -3- engage.
– Press the lever -2- located on the brake caliper in direction of
-arrow- and engage the brake cable -1-.
The brake cable must be installed without tension between the
bracket on the brake caliper and the bracket on the rear axle.
– Install the parking brake cable -2- in the compensator bracket
-3-.
– Pay attention that the guide tube is seated correctly in the
mount -item 9-
– Pretension the parking brake cable using the adjustment nut
-1-.
– Adjust the parking brake. Refer to
⇒ “3.2 Parking Brake, Adjusting”, page 81
Tightening Specification
♦ Refer to ⇒ Body Interior; Rep. Gr. 68 ; Center Console; Over‐
view - Center Console .
♦ For installing the wheel bolts. Refer to ⇒ Suspension, Wheels,
Steering; Rep. Gr. 44 ; Wheels and Tires; Wheel Bolt Tight‐
ening Specifications .
3.3.2
Rear Brake Cable, Torsion Beam Axle,
Removing and Installing
Removing
– Loosen the wheel bolts.
– Raise the vehicle.
– Remove the wheel.
– Loosen the parking brake lever.
• Parking brake lever in released position.
– Press the lever -2- located on the brake caliper in the direction
of the -arrow- and disengage the brake cable -1-.
– Squeeze the tabs -3- and remove the brake cable from the
bracket -4- on the brake caliper.
– Remove the center console. Refer to ⇒ Body Interior; Rep.
Gr. 68 ; Center Console; Overview - Center Console .
– Loosen the adjusting nut -1- until it is possible to disengage
the parking brake cable -2- from the compensator bracket
-3-.
– Disengage the brake cable -1- from the bracket -3- and pull it
from the guide tube -2-.
– Release the bracket from the rear axle and remove upward.
– Remove the brake cable rearward from the guide bushing on
the rear axle.
Installing
Install in reverse order of removal. Note the following:
– Guide the brake cable from the rear in the guide bushing.
– Clip in the bracket on the rear axle.
– Check for secure fit by pulling on it.
– Pay attention that the guide tube and the seal are seated cor‐
rectly.
– Push the brake cable -1- in the guide tube -2- until stop.
– Engage the brake cable -1- in the bracket -3- and push in wire.
– Engage the brake cable at the marking -arrow-.
– Push the brake cable -1- through the bracket -4- on the brake
caliper until both tabs -3- engage.
– Press the lever -2- located on the brake caliper in the direction
of the -arrow- and engage the brake cable -1-.
The brake cable must be installed without tension between the
bracket on the brake caliper and the bracket on the rear axle.
– Install the parking brake cable -2- in the compensator bracket
-3-.
– Pay attention that the guide tube is seated correctly in the
mount -item 9-
– Pretension the parking brake cable using the adjustment nut
-1-.
– Adjust the parking brake. Refer to
⇒ “3.2 Parking Brake, Adjusting”, page 81
Tightening Specification
♦ Refer to ⇒ Body Interior; Rep. Gr. 68 ; Center Console; Over‐
view - Center Console .
♦ For installing the wheel bolts. Refer to ⇒ Suspension, Wheels,
Steering; Rep. Gr. 44 ; Wheels and Tires; Wheel Bolt Tight‐
ening Specifications .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст