Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 967
2.23
Driver and Front Passenger Door Con‐
tact Switch - F2- / -F3- , Removing and
Installing
The door contact switch is installed in the door lock and cannot
be replaced individually when faulty.
– Removing and installing the front door lock. Refer to ⇒ Body
Exterior; Rep. Gr. 57 ; Door Components; Door Lock, Re‐
moving and Installing .
2.24
Driver and Passenger Side Rear Power
Window Button -E711- / -E713- , Re‐
moving and Installing
The removal and installation is described for the left side. Re‐
moving and installing on the right side is identical.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the rear door trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Rear Door Trim Panels; Rear Door Trim Panel,
Removing and Installing .
– Release the hook in the direction of the -arrow A- with a small
screwdriver.
– Release the mounting tab -2- in the direction of the
-arrow B-.
– Remove the window regulator switch -3- from the switch
mount and remove it to the rear.
– Release and disconnect the connector -1-.
Installing
Install in reverse order of removal.
– Perform a function test.
2.25
Left/Right Rear Door Contact Switch -
F10- / -F11- , Removing and Installing
The door contact switch is installed in the door lock and cannot
be replaced individually when faulty.
– Removing and installing the rear door lock. Refer to ⇒ Body
Exterior; Rep. Gr. 58 ; Door Components; Door Lock, Re‐
moving and Installing .
2.26
Start System Button - E378- , Removing
and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the selector lever boot. Refer to ⇒ Rep. Gr. 34 ;
Selector Mechanism; Selector Lever Handle, Removing and
Installing .
– Remove the Start System Button - E378- -1- from below out
of the center console -2-. The clips are opened at the same
time.
– Release and disconnect the connectors.
Installing
Install in reverse order of removal.
– Perform a function test.
2.27
Rear Lid Contact Switch, Removing and
Installing
The rear lid contact switch is installed in the rear lid latch and
cannot be replaced separately.
– Rear Lid Latch, Removing and installing. Refer to ⇒ Body Ex‐
terior; Rep. Gr. 55 ; Rear Lid; Lid Latch, Removing and
Installing .
2.28
Driver and Front Passenger Vanity Mir‐
ror Lamp Contact Switch - F147- / -
F148- , Removing and Installing
The vanity mirror contact switch is installed in the sun visor mount
and cannot be replaced separately if faulty.
– Sun Visor, removing and installing. Refer to ⇒ Body Interior;
Rep. Gr. 68 ; Equipment; Sun Visor, Removing and Installing .
2.29
Sunroof Button - E325- , Removing and
Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the Front Interior Lamp - WX1- . Refer to
⇒ “2.30 Front Interior Lamp/Reading Lamp, Removing and In‐
– Remove the bolts -arrows-.
– Remove the button -1- from the interior lamp.
Installing
Install in reverse order of removal.
– Perform a function test.
Tightening Specifications
♦ Refer to
2.30
Front Interior Lamp/Reading Lamp, Re‐
moving and Installing
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
The switch module is a component of the Front Interior Lamp -
WX1- and cannot be removed separately.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the mirror base cover. Refer to ⇒ Body Interior; Rep.
Gr. 68 ; Rearview Mirror; Overview - Rearview Mirror .
– Pry the diffusion lens in the marked areas -arrows- using the
-3409- from the Front Interior Lamp - WX1- .
Only Front Interior Lamp - WX1- with LED-Technology
– Release and disconnect the connectors.
All Versions
– Push the catches in the direction of the -arrow A- and remove
the Front Interior Lamp - WX1- .
– Release and disconnect the connectors.
Installing
Install in the reverse order of removal while paying attention to
the following:
– Install the Front Interior Lamp - WX1- in the roof opening.
– Install the diffusion lens in the Front Interior Lamp - WX1- .
– Perform a function test.
2.31
Rear Interior Lamp/Reading Lamp, Re‐
moving and Installing
The button is a permanent component of the Rear Interior Lamp
- WX2- and cannot be removed separately.
Caution
Risk of damaging the component surfaces.
♦ When positioning a prying tool, put commercially available
adhesive tape over the component in the visible area.
The Rear Interior Lamp - WX2- is held in place by a dual-stage
locking mechanism.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Pry the diffusion lens -1- with a narrow screwdriver in the di‐
rection of the -arrow A-.
– Remove the diffusion lens -1- from the Rear Interior Lamp -
WX2- -2-.
– Release the catches -2- with a narrow screwdriver in the di‐
rection of the -arrow A-.
– Push the locking mechanism -1- in the direction of the
-arrow B-.
– Remove the Rear Interior Lamp - WX2- -1- out of the roof
opening in the direction of the -arrow A-.
– Release the connector safety catch in the direction of the
-arrow B- and disconnect the connector in the direction of the
-arrow C-.
Installing
Install in the reverse order of removal while paying attention to
the following:
Note
The connector must point in the direction of travel/
– Push the locking mechanism -1- opposite the direction of the
-arrow B-. The catches -2- must engage securely.
– Perform a function test.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст