Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 984
2.6.2
Left/Right Rear Bass Speaker -R15- / -
R17- , 4-Door Vehicles, Removing and
Installing
The Left Rear Bass Speaker - R15- / Right Rear Bass Speaker -
R17- are located at the bottom of the rear doors.
The removal and installation is described for the left side. Re‐
moving and installing on the right side is identical.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the rear door trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Rear Door Trim Panels; Rear Door Trim Panel,
Removing and Installing .
– Release and disconnect the connector -1- from the bass
speaker in the direction of the -arrow-.
– Drill out the rivets -1- using a suitable drill.
– Remove the bass speaker.
Caution
Always remove any shavings resulting from the drilling, other‐
wise they may cause corrosion damage later.
If the paint on the door frame gets damaged during drilling,
touch-up immediately.
Installing
Install in reverse order of removal. Note the following:
– Secure the speaker using special blind rivets when installing
(Note the part number. Refer to the Parts Catalog).
2.7
Left/Right Front Bass Speaker -R21- / -
R23- , Removing and Installing
The Left Front Bass Speaker - R21- / Right Front Bass Speaker
- R23- are located at the bottom of the front doors.
The removal and installation is described for the left side. Re‐
moving and installing on the right side is identical.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the front door trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Front Door Trim Panels; Front Door Trim Panel,
Removing and Installing .
– Release and disconnect the connector -1- from the bass
speaker in direction of -arrow-.
– Drill out the rivets -1- using a suitable drill.
– Remove the bass speaker.
Caution
Always remove any shavings resulting from the drilling, other‐
wise they may cause corrosion damage later.
If the paint on the door frame gets damaged during drilling,
touch-up immediately.
Installing
Install in reverse order of removal. Note the following:
– Secure the speaker using special blind rivets when installing
(Note the part number. Refer to the Parts Catalog).
2.8
Subwoofer - R211- , Removing and In‐
stalling
⇒ “2.8.1 Subwoofer R211 , Removing and Installing, Sedan”,
page 26
⇒ “2.8.2 Subwoofer R211 , Removing and Installing, Wagon”,
2.8.1
Subwoofer - R211- , Removing and In‐
stalling, Sedan
The Subwoofer - R211- is located in the spare wheel well.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the luggage compartment floor.
– Release and disconnect the connector -2- from the Subwoofer
- R211- -1-.
– Remove the bolt -3- on the Subwoofer - R211- -1-.
– Remove the Subwoofer - R211- -1- upward.
Installing
Install in reverse order of removal.
Tightening Specifications
Component
Tightening Specification
Bolt -3- to the Subwoofer - R211-
9 Nm
2.8.2
Subwoofer - R211- , Removing and In‐
stalling, Wagon
The Subwoofer - R211- is located in the spare wheel well.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Fold up the luggage compartment floor.
– Release and disconnect the connector -3- from the Subwoofer
- R211- -1-.
– Remove the bolt -2- on the Subwoofer - R211- -1-.
– Remove the Subwoofer - R211- -1- upward.
Installing
Install in reverse order of removal.
Tightening Specifications
Component
Tightening Specification
Bolt -2- to Subwoofer - R211-
9 Nm
3
Antenna Systems
⇒ “3.1 Component Location Overview - Antenna Systems”, page
28
⇒ “3.2 AM Frequency Filter R177 , Removing and Installing”,
page 31
⇒ “3.3 FM Frequency Filter in the Negative Wire R178 / FM Fre‐
quency Filter in the Positive Wire R179 , Removing and Installing”,
page 32
⇒ “3.4 Antenna Module, Removing and Installing”, page 32
⇒ “3.5 Roof Antenna, Removing and Installing”, page 35
3.1
Component Location Overview - Anten‐
na Systems
⇒ “3.1.1 Component Location Overview - Antenna Systems, Se‐
dan”, page 28
⇒ “3.1.2 Component Location Overview - Antenna Systems,
3.1.1
Component Location Overview - Antenna Systems, Sedan
1 - FM Frequency Filter in Pos‐
itive Wire - R179-
❑ On the left window
frame of the rear lid
❑ FM plus trap circuit
❑ Its function is to prevent
antenna signals from
shorting to ground
❑ Removing and instal‐
ling. Refer to
2 - AM Frequency Filter -
R177-
❑ On the lower right of the
rear lid
❑ Its function is to prevent
antenna signals from
shorting to ground
❑ Removing and instal‐
ling. Refer to
3 - FM Frequency Filter in Neg‐
ative Wire - R178-
❑ On the right window
frame of the rear lid
❑ FM minus trap circuit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст