Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 21
– Retainer the retaining tabs -3-.
Caution
There is a danger of leaks.
♦ The windshield washer fluid reservoir is one part. Sepa‐
rating between the washer fluid reservoir, filler tube and
filler neck is not possible. If the components are separated
nevertheless the connection can leak.
– Remove the filler neck -1- upward from the lock carrier -2-
bracket.
– Release and disconnect the connectors -2 and 3-.
– Release the clips -6- in the direction of the arrow -A-.
– Remove the washer fluid hoses -4 and 5- from the Windshield
and Rear Window Washer Pump - V59- .
– Loosen the wiring harness from the washer fluid reservoir
-1-.
– Remove the nuts -1, 2 and 3-.
– Remove the washer fluid reservoir -4- from the threaded pins.
Installing
Install in the reverse order of removal while paying attention to
the following:
In order to prevent interchanging washer fluid line connections at
Windshield and Rear Window Washer Pump - V59- , connections
at pump and hose lines are marked with colors. Hose connector
pieces must be connected to the corresponding colored pump
connections during installation.
Tightening Specifications
♦ Refer to
⇒ “2.1 Overview - Windshield Washer System”, page 69
2.3
Windshield Washer Fluid Level Sensor,
Removing and Installing
Special tools and workshop equipment required
♦ Drip Tray
The Windshield Washer Fluid Level Sensor - G33- can depending
on version be replaced individually or only with the entire con‐
tainer.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the left front wheel housing liner. Refer to ⇒ Body
Exterior; Rep. Gr. 66 ; Wheel Housing Liner; Front Wheel
Housing Liner, Removing and Installing .
– Place a drip tray under the washer fluid reservoir.
– Release and disconnect the connector -2-.
– Remove the Windshield Washer Fluid Level Sensor - G33-
-1- from the washer fluid reservoir.
– When necessary remove the seal -3- from the washer fluid
reservoir.
Installing
Install in the reverse order of removal while paying attention to
the following:
– Install the seal correctly in the opening in the washer fluid res‐
ervoir.
– Coat the seal with washer fluid, so that the Windshield Washer
Fluid Level Sensor - G33- can be easily pushed in.
2.4
Windshield Washer Pump, Removing
and Installing
Special tools and workshop equipment required
♦ Drip Tray
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the left front wheel housing liner. Refer to ⇒ Body
Exterior; Rep. Gr. 66 ; Wheel Housing Liner; Front Wheel
Housing Liner, Removing and Installing .
– Release and disconnect the connector -1-.
The wiring harness -2- remains in the washer fluid reservoir.
– Place a drip tray under the washer fluid reservoir.
– Release the clamps -3 and 4- in the direction of -arrow A-.
– Remove the washer fluid hose from the Windshield and Rear
Window Washer Pump - V59- -5-.
– Remove the Windshield and Rear Window Washer Pump -
V59- -5- upward in the direction of -arrow B- from the washer
fluid reservoir.
Installing
Install in the reverse order of removal while paying attention to
the following:
In order to prevent interchanging washer fluid line connections at
Windshield and Rear Window Washer Pump - V59- , connections
at pump and hose lines are marked with colors. Hose connector
pieces must be connected to the corresponding colored pump
connections during installation.
– Check the sealing grommet for damage.
2.5
Spray Nozzles, Removing and Installing
The removal and installation is described for the left side. Re‐
moving and installing on the right side is identical.
Removing
– Open the hood.
– Push the spray nozzle upward -arrow A- and tilt it out from
under the flap -arrow B-.
– Release the hose clip -1- in the direction of -arrow- and remove
the hose connection -2- from the spray nozzle -4-.
– Disconnect the connector -3- and remove the spray nozzle
-4-.
Installing
Install in the reverse order of removal while paying attention to
the following:
When connecting the washer fluid line, ensure that the securing
clip engages audibly into the connection.
– Starting at the top, slide the spray nozzle into the installation
opening until it engages audibly.
– Adjust the spray nozzles. Refer to
⇒ “2.6 Spray Nozzles, Adjusting”, page 75
2.6
Spray Nozzles, Adjusting
Caution
Risk of damage.
♦ Do not use any objects to clean the spray nozzles!
Remove the spray nozzles if the spraying field is uneven due to
dirt in the nozzle, and flush out in the opposite direction of the
spray. It is permissible to further blow through in opposite direc‐
tion of spray with compressed air. Do not use any objects to clean
the spray nozzles!
– Adjusting washer nozzles for front windshield washer system.
Refer to ⇒ Maintenance ; Booklet 36.1 ; Procedure Descrip‐
tions .
3
Rear Window Wiper System
⇒ “3.1 Overview - Rear Window Wiper System”, page 76
⇒ “3.2 Wiper Blade, Removing and Installing”, page 77
⇒ “3.3 Windshield Wiper Arm, Removing and Installing”,
page 77
⇒ “3.4 Wiper Arm, Adjusting”, page 78
⇒ “3.5 Rear Window Wiper Motor V12 , Removing and Installing”,
3.1
Overview - Rear Window Wiper System
1 - Cap
2 - Nut
❑ 12 Nm
3 - Wiper Arm with Joint-Free
Windshield Wiper
❑ Removing and instal‐
ling. Refer to
❑ Park position, adjusting.
Refer to
.
❑ Joint-free windshield
wiper, removing and in‐
stalling. Refer to
4 - Seal
❑ Inside the rear window
❑ Replace if damaged.
Refer to
❑ Removing and instal‐
ling. Refer to
5 - Rear Window Wiper Motor
- V12-
❑ Removing and installing. Refer to
⇒ “3.5 Rear Window Wiper Motor V12 , Removing and Installing”, page 78
.
6 - Nut
❑ 8 Nm
❑ Quantity: 3
7 - Rubber Ring
❑ Quantity: 3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст