Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 381
11.2
Seat Position Sensor, Removing and In‐
stalling
Removing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
.
♦ Before handling pyrotechnic components (for example,
disconnecting the connector), the person handling it must
“discharge static electricity”. This can be done by touching
the door striker pin, for example.
– Remove the front seat. Refer to
⇒ “2.10 Front Seat, Removing and Installing”, page 335
– Attach the front seat to the Fixture For Seat Repair . Refer to
⇒ “1.2 Front Seat, Mounting on Fixture for Seat Repair”, page
.
– Remove the bolt -3-.
– Release the hook -arrow- of the seat position sensor -2- from
the seat pan lower frame -1-.
Note
It may be helpful to make drawings or take photos of the wire
routing. This assures the wires will be reconnected correctly.
– Disconnect the wire from the seat position sensor and free it
up.
– Remove the seat position sensor with the wires from the seat
pan lower frame.
Installing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
♦ Before handling pyrotechnic components (for example,
disconnecting the connector), the person handling it must
“discharge static electricity”. This can be done by touching
the door striker pin, for example.
Install in reverse order of removal. Note the following:
Note
♦
Make sure the connectors are pushed in all the way and that
they engage audibly.
♦
Make sure the wires are not pinched.
WARNING
The ignition must be on when connecting the battery. If pyro‐
technic components (for example, airbag, belt tensioner) are
not repaired correctly, they may deploy unintentionally after
connecting battery. There must not be anyone inside the ve‐
hicle when connecting the battery.
– Connect the battery ground cable with the ignition turned on.
Refer to ⇒ Electrical Equipment; Rep. Gr. 27 ; Battery; Bat‐
tery, Disconnecting and Connecting .
WARNING
If the ignition is not switched on after the battery is reconnected
- “indicator lamps in the instrument cluster do not light up” - the
ignition (key/button) may only be switched on when the driver
seat is positioned all the way back.
Note
If the Airbag Indicator Lamp - K75- indicates a fault, check the
DTC memory, erase it and check it again using the Vehicle Di‐
agnostic Tester .
Tightening Specifications
♦ Refer to
12
Belt Fastening Detection
⇒ “12.1 Front Passenger Occupant Detection Sensor G128 , Re‐
moving and Installing”, page 175
12.1
Front Passenger Occupant Detection
Sensor - G128- , Removing and Instal‐
ling
Note
The passenger occupant detection sensor is only installed in the
front passenger seat.
Removing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
♦ Before handling pyrotechnic components (for example,
disconnecting the connector), the person handling it must
“discharge static electricity”. This can be done by touching
the door striker pin, for example.
– Disconnect the battery ground cable with the ignition turned
on. Refer to ⇒ Electrical Equipment; Rep. Gr. 27 ; Battery;
Battery, Disconnecting and Connecting .
– Remove the front passenger seat. Refer to
⇒ “2.10 Front Seat, Removing and Installing”, page 335
.
– Remove the seat pan cover and cushion. Refer to
⇒ “1.4 Seat Pan Cover and Cushion, Removing and Installing”,
.
– Disconnect the connector for the passenger occupant detec‐
tion system pressure sensor.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст