Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 382
– Unclip the clips -1- from the seat backrest and remove the
passenger occupant detection system pressure sensor -2-.
Installing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
.
♦ Before handling pyrotechnic components (for example,
connecting the connector), the person handling it must
“discharge static electricity”. This can be done by touching
the door striker pin, for example.
Caution
The new passenger occupant detection system pressure sen‐
sor should be installed in the same location as the old sensor.
Install in reverse order of removal while paying attention to the
following:
– Push the clips for the passenger occupant detection system
pressure sensor into the seat pan until they click into place.
Note
Make sure the connectors are pushed in all the way and that they
engage audibly.
WARNING
The ignition must be on when connecting the battery. If pyro‐
technic components (for example, airbag, belt tensioner) are
not repaired correctly, they may deploy unintentionally after
connecting battery. There must not be anyone inside the ve‐
hicle when connecting the battery.
– Connect the battery ground cable with the ignition turned on.
Refer to ⇒ Electrical Equipment; Rep. Gr. 27 ; Battery; Bat‐
tery, Disconnecting and Connecting .
WARNING
If the ignition is not switched on after the battery is reconnected
- “indicator lamps in the instrument cluster do not light up” - the
ignition (key/button) may only be switched on when the driver
seat is positioned all the way back.
Note
If the Airbag Indicator Lamp - K75- signals a fault after installing,
check the DTC memory, erase it and check it again use the Ve‐
hicle Diagnostic Tester .
13
Passenger Occupant Detection Sys‐
tem
⇒ “13.1 Overview - Passenger Occupant Detection System”,
page 178
⇒ “13.2 Passenger Occupant Detection System Pressure Sensor,
Removing and Installing”, page 180
⇒ “13.3 Passenger Occupant Detection System Control Module
J706 , Removing and Installing”, page 186
⇒ “13.4 Passenger Occupant Detection System Control Module
J706 Bracket, Removing and Installing”, page 189
13.1
Overview - Passenger Occupant Detection System
Note
♦
The passenger occupant detection system pressure sensor automatically deactivates the front passenger
airbag when the front passenger seat is not occupied.
♦
The passenger occupant detection system pressure sensor and the Front Passenger Seat Heating Element
- Z8- are a shared component.
♦
This equipment is only installed on vehicles released in the USA.
♦
The components pictured can vary in form and appearance from the present vehicle. However the assembly
and functionality are identical.
1 - Wiring Harness
❑ Pay attention to the ex‐
act wire routing. Refer to
.
2 - Front Seat Cushion
❑ Must not be disconnec‐
ted from the passenger
occupant detection sys‐
tem pressure sensor
❑ The components are
separated from each
other; replace both com‐
ponents
❑ It is not necessary to re‐
place the Passenger
Occupant Detection
System Control Module
- J706- .
3 - Positioning Aids
❑ Positioning aids on the
passenger occupant de‐
tection system pressure
sensor
4 - Passenger Occupant De‐
tection System Pressure Sen‐
sor
❑ Must not be separated
from the front seat cush‐
ion cover
❑ The components are
separated from each
other; replace both com‐
ponents
❑ On vehicles with seat heating, the passenger occupant detection system pressure sensor and the Front
Passenger Seat Heating Element - Z8- are a shared component.
❑ It is not necessary to replace the Passenger Occupant Detection System Control Module - J706- .
❑ Removing and installing. Refer to
⇒ “13.2 Passenger Occupant Detection System Pressure Sensor, Removing and Installing”,
.
5 - Positioning Aids
❑ Positioning aids on the front seat cushion padding
6 - Adhesive Surfaces
❑ Adhesion surface for gluing to the front seat cushion cover
7 - Screw
❑ 1.5 Nm
❑ Screw for Passenger Occupant Detection System Control Module - J706-
8 - Bracket
❑ Passenger Occupant Detection System Control Module - J706- bracket
❑ Clipped to the seat frame
❑ Removing and installing. Refer to
⇒ “13.4 Passenger Occupant Detection System Control Module J706 Bracket, Removing and Installing”,
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст