Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 970
5.2
Cigarette Lighter - U1- , Removing and
Installing
All instructions and information on this chapter. Refer to ⇒ Elec‐
trical Equipment General Information; Rep. Gr. 96 ; Cigarette
Lighter and Socket .
5.3
Socket Illumination Bulb - L42- , Remov‐
ing and Installing
All instructions and information on this chapter. Refer to ⇒ Elec‐
trical Equipment General Information; Rep. Gr. 96 ; Cigarette
Lighter and Socket .
5.4
Rear Cigarette Lighter Illumination Bulb
- L32- , Removing and Installing
All instructions and information on this chapter. Refer to ⇒ Elec‐
trical Equipment General Information; Rep. Gr. 96 ; Cigarette
Lighter and Socket .
5.5
Socket - U- , Removing and Installing
All instructions and information on this chapter. Refer to ⇒ Elec‐
trical Equipment General Information; Rep. Gr. 96 ; Cigarette
Lighter and Socket .
5.6
Converter with Socket, 12 V-230 V -
U13- , Removing and Installing
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
WARNING
There is a danger of electric shock.
♦ The Converter with Socket, 12 V-230 V - U13- housing
contains condensers that can be charged with residual
voltage.
♦ The Converter with Socket, 12 V-230 V - U13- housing
must not be opened under any circumstances.
♦ No repairs may be performed on the harness connector,
on the wires and the 230 V-outlet.
♦ If there is a fault at harness connector, at wires, at 230 V-
socket or in the converter, the complete unit must always
be replaced.
Caution
Risk of damaging the component surfaces.
♦ When positioning a prying tool, put commercially available
adhesive tape over the component in the visible area.
Removing:
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the right luggage compartment side trim panel. Refer
to ⇒ Body Interior; Rep. Gr. 70 ; Luggage Compartment Trim
Panels; Luggage Compartment Side Trim Panel, Removing
and Installing .
– Release and disconnect the connector -1-.
– Remove the screws -4 and 5-.
– Remove the Converter with Socket, 12 V-230 V - U13- -2- with
the bracket -3-.
– Remove the bolts -3-.
– Remove the Converter with Socket, 12 V-230 V - U13- -1- from
the bracket -2-.
Installing:
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
6
Special Tools
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
97 – Wiring
1
Relay Carriers, Fuse Panels and E-
Boxes
⇒ “1.1 Component Location Overview - Relay Carriers, Fuse
Panels and E-Boxes”, page 288
⇒ “1.2 E-Box, Removing and Installing”, page 290
⇒ “1.3 E-Box Relay and Fuse Panels, Removing and Installing”,
page 292
⇒ “1.4 Relay and Fuse Carrier Behind Instrument Panel on Driver
Side, Removing and Installing”, page 294
1.1
Component Location Overview - Relay
Carriers, Fuse Panels and E-Boxes
⇒ “1.1.1 Relay Carriers, Fuse Panels and E-Boxes”, page 288
⇒ “1.1.2 Relay Carrier and Instrument Panel/A-Pillar Fuse Panel”,
1.1.1
Relay Carriers, Fuse Panels and E-Boxes
1 - Front Cover
❑ For engine compart‐
ment E-box
2 - Nut
❑ 9 Nm
3 - Nut
❑ 9 Nm
4 - Wire
❑ 5 Nm
❑ Coolant fan
5 - Wire
❑ 5 Nm
❑ Terminal 30
6 - Wire
❑ 5 Nm
❑ Electro-mechanical
power steering
7 - Wire
❑ 6 Nm
❑ Battery positive
8 - Wire
❑ 5 Nm
❑ Terminal 30
9 - Wire
❑ 6 Nm
❑ Generator - C-
10 - Fuse Panel A - SA-
❑ Removing and instal‐
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст