Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 971
⇒ “1.3.2 Fuse Panel A SA , Removing and Installing”, page 293
.
11 - Mounting Bracket
❑ Removing and installing. Refer to
⇒ “1.3.2 Fuse Panel A SA , Removing and Installing”, page 293
.
12 - Cover
❑ For engine compartment E-box
13 - Relay and Fuse Panel B - SB-
❑ With connecting bracket for fuse panel A
❑ Removing and installing. Refer to
⇒ “1.3 E-Box Relay and Fuse Panels, Removing and Installing”, page 292
.
14 - Wire
❑ 6 Nm
15 - Bracket
❑ For Engine Control Module - J623-
16 - Engine Compartment E-Box
❑ Removing and installing. Refer to
1.1.2
Relay Carrier and Instrument Panel/A-Pillar Fuse Panel
Note
The Sedan is shown. The Wagon is identical.
1 - Bracket
❑ For Parking Aid Control
Module - J446- / Parallel
Parking Assistance
Control Module - J791-
❑ Removing and instal‐
ling. Refer to
.
2 - Bracket
❑ For Vehicle Electrical
System Control Module
- J519-
❑ Removing and instal‐
ling. Refer to
.
3 - Fuse Panel C - SC-
❑ Removing and instal‐
ling. Refer to
4 - Screw
❑ 3 Nm
❑ Quantity: 3
1.2
E-Box, Removing and Installing
Removing
– Disconnect the Battery - A- . Refer to
⇒ “1.3 Battery, Disconnecting and Connecting”, page 9
.
– Remove the Engine Control Module - J623- and set it aside
with the connectors attached. Refer to ⇒ Rep. Gr. 23 ; Engine
Control Module; Engine Control Module - J623- , Removing
and Installing or ⇒ Rep. Gr. 24 ; Engine Control Module; En‐
gine Control Module - J623- , Removing and Installing .
– Push the release button in direction of -arrows-.
– Remove the engine compartment E-box cover -1-.
– Release the mounting tab -2- with a screwdriver, and remove
the front cover -1- upward in direction of -arrow-.
– Cut the lower cable ties on the wiring harness.
– Release the retainers -1, 2 and 4- -arrow- and remove the fuse
panel B -3- and set it aside.
– Remove the nuts -arrows- and remove the Engine Control
Module - J623- -1- bracket.
– Release the mounting tab -3- and disengage the engine com‐
partment E-box -2- from the threaded pin.
– Remove the engine compartment E-box upward.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “1.1.1 Relay Carriers, Fuse Panels and E-Boxes”,
1.3
E-Box Relay and Fuse Panels, Remov‐
ing and Installing
⇒ “1.3.1 Fuse Panel B SB , Removing and Installing”,
page 292
⇒ “1.3.2 Fuse Panel A SA , Removing and Installing”,
1.3.1
Fuse Panel B - SB- , Removing and In‐
stalling
Removing
– Disconnect the Battery - A- . Refer to
⇒ “1.3 Battery, Disconnecting and Connecting”, page 9
.
– Press the release buttons in direction of -arrow- and remove
the cover -1- for the engine compartment E-box.
– Release the mounting tab -2- with a screwdriver, and remove
the front cover -1- upward in direction of -arrow-.
– For reinstallation, mark the wires at the bolted connections.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст