Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 866
Drive Off Cover for Inner Joint
Removing the Inner CV Joint
– Press off CV from joint using drift.
– Remove the circlip.
– Remove both clamps, and push the CV boot toward outer joint.
Assembling
Installed Location of the Plate Spring on Inner Joint
1 - Plate Spring
Pressing On Inner CV Joint
Note
Chamfer on inner diameter of ball hub (splines) must face the
contact shoulder on the drive axle.
– Press on joint until stop.
– Install the circlip.
– Align new cover with bolts -arrows- to bolt holes.
Note
It must be aligned exactly because it cannot be aligned after driv‐
ing on.
– Drive cover on with a plastic hammer.
Tightening Clamping Sleeve on Outer Joint
– Position Clamping Pliers - VAG1682A- as shown in illustration.
When doing this, make sure that edges of clamping pliers are
seated in corners -arrows B- of clamp.
– Tension clamp by turning spindle with a torque wrench (do not
tilt clamp tool).
Note
♦
The hard material of the joint boot (compared to rubber) makes
it necessary to use a stainless steel hose clamp. It is only pos‐
sible to tighten the hose clamp with Clamping Pliers -
VAG1682A- .
♦
Tightening specification: 25 Nm.
♦
Use torque wrench -C- with adjustment range 5 to 50 Nm (for
example Torque Wrench 5-50Nm - VAG1331- ).
♦
Be sure thread of spindle -A- of clamp tool moves freely.
Grease with MOS 2 grease if necessary.
♦
If the thread is tight, for example, dirty, the required tensioning
force for the hose clamp will not be achieved in spite of correct
torque specification settings.
Tensioning Clamp on Small Diameter
8.5
Outer CV Joint, Checking
The joint is to be disassembled if badly contaminated to replace
the grease, or when the ball contact surfaces show wear or dam‐
age.
Removing
– Before disassembling mark ball hub position in relation to the
ball cage and housing with an electro-writer or oil stone
-arrow-.
– Tilt ball hub and ball cage and remove balls one after another.
– Turn cage until the two rectangular windows -arrow- are
aligned with the joint housing.
– Lift out cage with hub.
– Swing a hub segment in a cage window.
– Fold hub out from cage.
Note
♦
The six balls of each joint belong to one tolerance group.
Check stub axle, hub, cage and balls for small depressions
(pitting build-up) and chafing.
♦
Excessive circumferential backlash in joint makes itself no‐
ticed via tip-in shock, in such cases joint should be replaced.
♦
Flattening and running marks of balls are no reason to replace
joint.
Installing
Install in reverse order of removal. Note the following:
– Press half of the grease amount from the repair kit into the joint
housing.
– Insert cage with hub into joint body.
Note
Cage must be installed laterally correct.
– Press in opposing balls in sequence, during this, previous po‐
sition of ball hub to ball cage and to joint body must be
established again.
– Install new circlip in shaft.
– Distribute remaining grease in the joint boot.
8.6
Inner CV Joint, Checking
The joint is to be disassembled if badly contaminated to replace
the grease, or when the ball contact surfaces show wear or dam‐
age.
Note
Ball hub and joint piece are paired. Before removing, mark in re‐
lation to each other using a waterproof felt-tip pen.
Removing
– Swivel the ball hub and ball cage.
– Remove the joint in the direction of the -arrow-.
– Remove the balls from the cage.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст