Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 405
Removing
Vehicles with Side Cushion
– Remove the side cushion. Refer to
⇒ “3.16 Side Cushion, Removing and Installing”, page 391
Vehicles without Side Cushion
– Remove the rear bench seat. Refer to
⇒ “3.7 Bench Seat/Single Seat, Removing and Installing”,
– Remove the nut -2-.
Continuation for All Vehicles
– Loosen the sill panel strip from the body and wheel housing
trim panel in the transition area to the wheel housing trim pan‐
el. Refer to
⇒ “5.10.2 Sill Panel Strip, Removing and Installing, 4-Door
.
– Fold the rear seat backrest forward.
– Loosen the wheel housing trim panel -1- from the C-pillar trim
panel using the Wedge Set - T10383- .
– Loosen the wheel housing trim panel -1- near the clips from
the body mounts using the Wedge Set - T10383- .
Installing
Note
♦
Check all the fasteners for damage and replace if necessary.
♦
Remove any remaining clips in the body mounting points using
the Omega Clip Tool - T40280- . To install, insert into the wheel
housing trim panel.
♦
Make sure that the wheel housing trim panel is inside the door
seal molding after installing.
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “5.8 Overview - Wheel Housing Trim Panel”, page 246
5.17.2
Wheel Housing Trim Panel, Removing
and Installing, Wagon
Note
The following describes the removing and installing on the left
side of the vehicle. Removing and installing on the right side is
identical.
Special tools and workshop equipment required
♦ Wedge Set - T10383-
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
Vehicles with Side Cushion
– Remove the side cushion. Refer to
⇒ “3.16 Side Cushion, Removing and Installing”, page 391
.
Vehicles without Side Cushion
– Remove the rear bench seat. Refer to
⇒ “3.7 Bench Seat/Single Seat, Removing and Installing”,
– Remove the nut -2-.
Continuation for All Vehicles
– Loosen the sill panel strip from the body and wheel housing
trim panel in the transition area to the wheel housing trim pan‐
el. Refer to
⇒ “5.10.2 Sill Panel Strip, Removing and Installing, 4-Door
.
– Fold the rear seat backrest forward.
– Loosen the wheel housing trim panel -1- from the C-pillar trim
panel -4- using the Wedge Set - T10383- .
– Loosen the wheel housing trim panel -1- near the clips -3- from
the body mounts using the Wedge Set - T10383- .
Installing
Note
♦
Check all the fasteners for damage and replace if necessary.
♦
Remove any remaining clips -3- in the body mounting points
using the Omega Clip Tool - T40280- . To install, insert into
the wheel housing trim panel.
♦
Make sure that the wheel housing trim panel is inside the door
seal molding after installing.
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “5.8 Overview - Wheel Housing Trim Panel”, page 246
5.18
Foot Rest, Removing and Installing
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Remove the lower A-pillar trim panel on the driver side. Refer
to
⇒ “5.12 A-Pillar Trim Panel, Removing and Installing”,
.
– Release the retainers -1-, unclip the foot rest -2- using the Trim
Removal Wedge - 3409- in direction of -arrows- and remove.
– Push aside the carpet in the area of the threaded connections
and remove the nuts -arrows-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст