Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 375
♦ Release Tool Set - Extraction Tool 17 - VAS1978/17- from the
Release Tool Set - VAS1978/35-
Removing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
.
♦ Observe the additional safety precautions for the head
curtain airbag. Refer to
⇒ “1.5 Additional Head Curtain Airbag Safety Precau‐
.
♦ Observe the disposal regulations for pyrotechnical com‐
ponents. Refer to
⇒ “1.3 Airbag, Belt Tensioner and Battery Cut-Out Units,
Storing, Transporting and Disposing (Pyrotechnic Com‐
.
– Disconnect the battery ground cable with the ignition turned
on. Refer to ⇒ Electrical Equipment; Rep. Gr. 27 ; Battery;
Battery, Disconnecting and Connecting .
– Remove the headliner. Refer to
⇒ “7.3 Headliner, Removing and Installing”, page 299
.
– Disengage the clips -1 through 5- in the head curtain airbag
mounting tabs from the vehicle body.
– To do so, forcefully push the Release Tool Set - Extraction
Tool 17 - VAS1978/17- with the »spoon« -arrow- all the way
into the opening -A-, as shown in the illustration.
– At the same time, pull the left side of the clip out of the vehicle
body.
– Pull the Release Tool Set - Extraction Tool 17 - VAS1978/17-
back out and make sure that the clips on the loosened side do
not re-engage.
– Turn the Release Tool Set - Extraction Tool 17 - VAS1978/17-
180°.
– Repeat the procedure on the opening -B-.
– Remove the clip -1- from the A-pillar.
WARNING
Before handling pyrotechnic components (for example, dis‐
connecting the connector), the person handling it must “dis‐
charge static electricity”. This can be done by touching the door
striker pin, for example.
– Remove the connector lock and remove the connector -1- from
the head curtain airbag -2- -arrow-.
– Remove the bolt -3- from the head curtain airbag.
– Disengage the head curtain airbag -1- from the mount on the
body in direction of -arrow B- and push rearward.
– Disengage the rear head curtain airbag from the mount on the
body in direction of -arrow A- and remove.
Installing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
.
♦ Always follow head curtain airbag installation procedure.
♦ Before handling pyrotechnic components (for example,
connecting the connector), the person handling it must
“discharge static electricity”. This can be done by touching
the door striker pin, for example.
– Engage the head curtain airbag -1- at the rear in the bracket
on the body in direction of -arrow A- and push forward.
– Engage the front head curtain airbag in the bracket on the body
in direction of -arrow B-.
– Attach the head curtain airbag with the bolt -1-.
– Turn the rearmost clip -1- downward 90° -arrow- and clip into
the vehicle body.
– Install the remaining head curtain airbag clips until they audibly
engage, toward the front and rear starting from the gas gen‐
erator
– Check the clips by pulling on them and make sure they are
completely engaged.
– Connect the connector to the head curtain airbag igniter.
– Press in the connector lock. This slides the connector into the
head curtain airbag igniter all the way and simultaneously
locks it.
– Make sure the anti-rotation protection line is visible along the
entire length and it is straight. By making sure it is will ensure
that the head curtain airbag is NOT twisted.
Install in reverse order of removal.
WARNING
The ignition must be on when connecting the battery. If pyro‐
technic components (for example, airbag, belt tensioner) are
not repaired correctly, they may deploy unintentionally after
connecting battery. There must not be anyone inside the ve‐
hicle when connecting the battery.
– Connect the battery ground cable with the ignition turned on.
Refer to ⇒ Electrical Equipment; Rep. Gr. 27 ; Battery; Bat‐
tery, Disconnecting and Connecting .
WARNING
If the ignition is not switched on after the battery is reconnected
- “indicator lamps in the instrument cluster do not light up” - the
ignition (key/button) may only be switched on when the driver
seat is positioned all the way back.
Note
If the Airbag Indicator Lamp - K75- indicates a fault, check the
DTC memory, erase it and check it again using the Vehicle Di‐
agnostic Tester .
Tightening Specifications
♦ Refer to
⇒ “8.1 Overview - Head Curtain Airbag”, page 147
8.2.2
Head Curtain Airbag with Igniter, Re‐
moving and Installing, Wagon
Special tools and workshop equipment required
♦ Release Tool Set - Extraction Tool 17 - VAS1978/17- from the
Release Tool Set - VAS1978/35-
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст