Volkswagen Golf Variant, Jetta. Manual — part 4
actuators have been renewed.
♦ Retainer also belongs to actuator.
There is no need to adjust anything if all the named parts have
only been removed and reinstalled.
Conditions:
• Only use tools in perfect condition.
• Contact surface of “gearbox on engine” must be free from “ir‐
regularities”. This guarantees straight edge makes good con‐
tact.
• Mechatronic unit is installed.
Perform the following steps:
Position of engagement bearings is comparable with clutch play
of a manual gearbox. In this 0AM dual clutch gearbox, there are
tolerances in engagement system of gearbox and in gearbox it‐
self. There are also tolerances within the dual clutch. These
tolerances must be considered separately when adjusting.
In the following procedure, you are first shown how to measure
all necessary dimensions “on gearbox”, in order to determine
what is the appropriate shim. Tolerances on gearbox and toler‐
ances in clutch determine thickness of shim.
First find a dimension “B”. This dimensions is required for both
clutches “K 1” and “K 2”.
Then find a dimension “A” for each clutch. The following 2 illus‐
trations show where to measure these dimensions.
Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤
1. Removing and installing the dual clutch
13
Note
Perform the following steps “in sequence” and precisely.
Adjusting:
– Install parts of clutch as far as large engaging lever
⇒ page 22
.
Do not install small engagement bearing, do not insert any shim.
Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤
14
It should lie sideways on shaft end.
Note
Ruler -T40100- should remain in this position during subsequent
measurements. Do not turn over, do not remove.
– Place digital depth gauge onto outer input shaft.
– “Zero” depth gauge.
– Measure distance from retaining ring.
– Note down result and call it “B”.
Example: “B” = 2.91 millimetres
Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤
1. Removing and installing the dual clutch
15
Do not measure on ring joint. This could force ring away at that
point and falsify measuring result.
– Remove retaining ring again.
This ring is not allowed to be installed again!
– Calculate average of both measuring results.
Example:
Dimension “B” = B1+B22 = 2,91+3,02 = 2.96
This dimension “B” is needed in the following calculations.
In the following sample calculations, “B” should be 2.96 mm. The
dimension given for “B” is and example. The value for “B” may be
different in another gearbox.
There are 2 clutches, therefore there are 2 setting procedures to
follow.
Each measurement requires different preparatory measures, as
well as a few calculations. Please comply with the following work‐
ing procedures.
Start by calculating shim for clutch “K 1”.
Do not insert any shim!
– Place gauge block -T10374- on “large” engagement bearing.
– Press once onto gauge block -T10374- whilst turning.
In this way, it is possible to observe how the engagement bearing
turns. This means gauge block -T10374- also “sits” correctly on
bearing.
– Place digital depth gauge “at top” onto outer input shaft.
Ruler -T40100- is already “on its side” on gearbox flange
⇒ page 15
.
Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤
16
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст