Volkswagen Fox (2004 year). Manual — part 58
indication.
– Follow the indications on the screen.
Note
This indication appears just before the engine temperature rea‐
ches 80 degrees Celsius.
– The engine temperature must reach the necessary level.
Measurement in high idle speed rotation:
It switches automatically to the high idle speed rotation measure‐
ment indication.
– Follow the indications on the screen.
The measurement starts as soon as the engine rotation reaches
the necessary level.
Note
♦
With the key
→
— it is possible to cancel the measurement,
that is, not perform the exhaust gas test.
♦
With the key
←
— the measurement values are reset and the
test can be repeated.
– Keep the engine rotation on the necessary level.
The remaining time for performing the measurement is indicated
on the space -arrow A-.
FOX 2004 ➤
5. Additional tasks due to country legislation
105
measurement and content of CO.
The measurement starts as soon as the engine rotation reaches
the necessary level.
The remaining time for performing the measurement is indicated
on the space -arrow A-.
Probe inspection test:
Note
The probe inspection test is not performed when all readiness
code values are at zero.
It switches automatically to the probe inspection test indication.
Note
The probe inspection test is performed individually for each Lamb‐
da Probe .
The measurement starts as soon as the engine rotation reaches
the necessary level.
– Keep the engine rotation on the necessary level.
The remaining time for performing the measurement is indicated
on the space -arrow A-.
Assessment:
After the exhaust gas test, the report will be displayed on the
screen.
The test result is indicated.
In this location, remarks about the exhaust gas test can be en‐
tered -arrow A-. They are included on the test report.
– After successfully performing the exhaust gas test, select on
the hanging menu - arrow B - “Assigned exhaust gas test plate”
and the date.
– Confirm with “Yes” - arrow C -.
– Then, press it.
FOX 2004 ➤
106
5. Additional tasks due to country legislation
ically printed.
– To get other certificates, press the -arrow A - “Print” button.
– Follow the indications on the screen.
– Remove the exhaust gas probe from the final exhaust gas
tube.
– Then, press
→
- arrow B-.
The exhaust gas test is concluded. It is possible to perform a new
exhaust gas test.
Exhaust gas test for petrol engines without OBD
Note
♦
All test conditions and data necessary for the exhaust gas test:
⇒ "Exhaust gas test"
♦
The ignition point is determined by the Engine control unit -
J623- and will not be indicated. It is not possible to make an
adjustment.
♦
The idle speed rotation and the content of CO cannot be ad‐
justed (just checked). If there are divergences between the
actual and the theoretical values: perform a Repair Measure!
♦
The content of CO is adjusted to the theoretical value by the
lambda probe adjustment. The defects in the lambda probe
inspections are processed by the Diagnosis, Measurement
and Information System -VAS 5051A /52- and stored in the
fault memory.
♦
When consulting the fault memory, the faults detected (elec‐
tronic engine system) must be eliminated and deleted from the
fault memory.
♦
To avoid injuries in people and/or destruction of ignition and
injection systems, the ignition system cables (also high volt‐
age cables) must be turned on and off only with the ignition
turned off.
Note
The following description refers to vehicles without OBD with cat‐
alytic converter adjusted.
Special tools and workshop equipment required
♦ Gas tester - 4 components (CO, CO2, HC and O2) or GAS
TESTER -VAS 6300-
♦ Adapter for older vehicles -VAS 5051/2-
FOX 2004 ➤
5. Additional tasks due to country legislation
107
Note
♦
It is only possible to perform an exhaust gas test when all de‐
vices from the Gas tester - 4 components (CO, CO2, HC and
O2) or GAS TESTER -VAS 6300- are working and connected
with one another, according to the operation instructions.
♦
All works to be performed are indicated by the Gas tester - 4
components (CO, CO2, HC and O2) or GAS TESTER -VAS
6300- .
Prior conditions for inspection:
• All conditions for inspection and data necessary for the ex‐
haust gas test are available on the exhaust gas test datasheet
for the respective engine⇒ Data sheets for exhaust emission
test.
• The exhaust gas test datasheet must be printed to enable the
barcode reading.
• Automatic gearbox: selector level in position “P” or “N”.
• Mechanical transmission: selector lever in “neutral gear”.
• Handbrake operated.
– Perform the exhaust gas test according to the instructions on
the screen.
Startup screen:
– Select the function-arrow-, “Exhaust gas test”.
The general view for selecting the respective type of exhaust gas
test will be displayed.
– Select “Petrol exhaust gas test” -arrow-.
FOX 2004 ➤
108
5. Additional tasks due to country legislation
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст