Volkswagen Fox (2004 year). Manual — part 16
Lubrication system components - re‐
move and install
Note
♦
When a significant number of metal chips and shavings ap‐
pear in the engine oil during engine repair due to crankshaft
and rod bearing wear, the oil filter must be replaced and the
oil gallery must be carefully cleaned.
♦
The oil level should not exceed the maximum marking - risk of
damage to the catalytic converter!
♦
All bearing and running surfaces must be lubricated before
assembly.
WARNING
Always replace self-locking nuts and screws subject to angular
torque
Check oil pressure
⇒ page 70
.
Oil system capacity:
with oil filter 4.2 l.
Engine oil specification:
Only use engine oils as per VW 505.01specification.
Part I assembly overview
⇒ page 61
.
Part II oil filter support disassembly
⇒ page 64
.
Part III: oil supply tube removal and installation
⇒ page 65
.
Part I
Fox 2004 ➤
1. Lubrication system components - remove and install
61
curing guides.
❑ Remove and install
⇒ page 17
.
❑ Install with Silicone
sealant -D 176 404 A2 -
⇒ page 17
❑ Do not apply additional
lubricant or grease to
the seal lip.
❑ Before installation, re‐
move oil residues from
crankshaft trunnion with
a clean cloth.
❑ Replace cranckshaft oil
sealing - pulley end
⇒ page 17
.
3 - Engine block
4 - Gasket
❑ Replace.
5 - Oil filter bracket
❑ Disassemble and as‐
semble
⇒ page 64
.
6 - 15 Nm + 90°
❑ Replace after each re‐
moval.
❑ First, fit upper left and
lower right bolts; then,
tighten the four bolts di‐
agonally.
7 - Oil dipstick
❑ The oil level should exceed the maximum marking!
❑ Marks
⇒ page 66
8 - Guide
❑ Remove to drain oil.
9 - 5 Nm
10 - Guide tube
11 - 10 Nm
❑ Not applicable.
12 - Sealing ring
❑ Replace.
❑ Check it is securely seated.
❑ Lubricate lightly when fitting.
13 - Cover
❑ With sealing tape.
❑ Clean filter if dirty.
Fox 2004 ➤
62
16 - Fastening sleeve
17 - 25 Nm
❑ Install without sealant.
18 - Mounting frame
❑ Before installing, check the centering guides in the engine block are in their positions, and the ring is
inserted in the mounting frame.
❑ Remove and install
⇒ page 23
.
19 - Oil ejector
❑ For piston cooling.
❑ Check installation position: Install by turning the oil ejector counterclockwise up to the stop.
20 - Sealing ring
❑ Replace.
21 - Crankcase
❑ Clean sealing surface before installation.
❑ Install with Silicone sealant -D 176 404 A2 -
⇒ page 68
22 - Support
❑ For intercooler hose.
23 - 15 Nm
24 - Packing
❑ Replace.
25 - Plug, 30 Nm
❑ Replace the plug with seal.
26 - Gear
❑ To oil pump.
❑ It can be installed in one position only.
27 - 20 Nm + 90°
❑ Replace after each removal.
28 - Chain
❑ Observe fastening position
⇒ page 23
.
29 - Gear
❑ To counterbalance shaft.
❑ It can be installed in one position only. The holes are displaced.
30 - 100 Nm + 90°
❑ Replace after each removal.
❑ The angular torque can be performed in several stages.
❑ To loose and tighten, use Multi-point spanner -T10061-
31 - Counterbalance
❑ It can be installed in one position only. The holes are displaced.
Fox 2004 ➤
1. Lubrication system components - remove and install
63
35 - Chain tensioning element with tensioning plate.
❑ To remove, immobilise with Locking pin -T10060- .
❑ Remove and install
⇒ page 23
.
36 - Sealing ring
❑ Not applicable.
37 - Oil level and temperature sensor -(G266)-
❑ Not applicable.
Part II
WARNING
Always replace self-locking nuts and screws subject to angular
torque
1 - Packing
❑ Replace.
2 - 15 Nm + 90°
❑ Replace after each re‐
moval.
❑ First, fit upper left and
lower right bolts; then,
tighten the four bolts di‐
agonally.
3 - Oil filter bracket
4 - Packing
❑ Replace.
5 - Connection, 25 Nm
❑ To the turbocharger oil
supply tube.
6 - Oil supply tube
❑ For the turbocompres‐
sor.
❑ Remove and install
⇒ page 65
.
7 - Oil pressure switch -F1- 0.7
bar, 20 Nm
❑ In case of leakage, cut
and replace the sealing
ring.
❑ Checking
⇒ page 70
.
8 - Sealing cap, 25 Nm
9 - Sealing ring
❑ Replace.
Fox 2004 ➤
64
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст