Volkswagen Jetta / Jetta Hybrid. Manual — part 3

and hose clamp

Removing pressure hose
Carry out following work:
– Loosen screw of hose clamp -A-.
– Pull pressure hose together with hose clamp -A- off the ribbed

union.

Fitting pressure hose
Carry out following work:

– Push pressure hose together with hose clamp -A- onto ribbed

union as far as it will go.

– Tighten screw of hose clamp -A-.

Caution

The hose clamp screw -A- must be tightened as prescribed

⇒ page 9

. If the tightening torque is too low or too high, the

pressure hose may slip off the ribbed union when the vehicle

is being driven.

Specified torque for hose clamps
1 - Hose clamp -a- = 13 mm wide: 5.5 Nm
2 - Hose clamp -b- = 9 mm wide: 3 Nm

Jetta 2011 ➤ , Jetta Hybrid 2013 ➤

1. Lock carrier

9

2.1

Tools

Special tools and workshop equipment required
♦ Torque wrench -V.A.G 1783-

Jetta 2011 ➤ , Jetta Hybrid 2013 ➤

10

Note

Only the left side is shown. The right side is similar.

1 - Wing

❑ Removing and installing

⇒ page 11

2 - Bolt

❑ Qty. 1, A-pillar.
❑ Qty. 2, wheel housing
❑ Qty. 1, side member
❑ Qty. 2, wing bracket
❑ Qty. 3, wing connection

piece

❑ Specified torque: 6 Nm.

3 - Wing end plate

❑ Removing and installing

⇒ page 15

4 - Insulation of wing end plate

❑ Placed in front of wing

end plate

⇒ page 14

❑ Not installed in all model

versions

5 - Foam element

❑ Inserted between wing

and longitudinal mem‐

ber for top of wheel arch

⇒ page 14

.

6 - Wing bracket

❑ Removing and installing

⇒ page 15

7 - Bolt

❑ Qty. 2.
❑ Specified torque: 6 Nm.

2.3

Removing and installing front wing

Note

The removal and installation sequence is only described for the

left wing. Removal and installation of the right wing is similar.

Jetta 2011 ➤ , Jetta Hybrid 2013 ➤

2. Wing

11

Carry out following work:
– Remove wheel housing liners

⇒ page 236

.

– Pull out foam between wing and longitudinal member

⇒ Item 5 (page 11)

.

– Pull out insulation of wing end plate, if it exists

⇒ Item 4 (page 11)

.

– Remove wing end plate

⇒ page 15

.

– Remove front bumper cover

⇒ page 175

.

– Remove guide at side for front bumper cover

⇒ page 179

.

– If featured, remove water channel

⇒ page 274

.

– Remove bolts -2-.
– Remove wing -1- carefully.

Jetta 2011 ➤ , Jetta Hybrid 2013 ➤

12

Была ли эта страница вам полезна?
Да!Нет
4 посетителя считают эту страницу полезной.
Большое спасибо!
Ваше мнение очень важно для нас.

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

Текст

Политика конфиденциальности