Kia Sedona (2008 year). Instruction — part 184
Fig. 172: Measuring Voltage Value Between Terminal 4 Of DDM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured voltage within specifications?
YES
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage.
Repair or replace as necessary and then go to "VERIFICATION OF VEHICLE REPAIR"
procedure.
NO
Substitute with a known-good DDM and check for proper operation.
If the problem is corrected, replace DDM and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B1910.
DTC B2332 ASSIST LOCK ACTUATOR ERROR
COMPONENT LOCATION
Refer to DTC B1912.
GENERAL DESCRIPTION
ADM is a node of CAN communication system which consists of IPM. FAM, RAM, DDM, IMS. Main
function of ADM is lock/unlock of door and window, adjusting position and fold/unfold of outside mirror. Door
lock actuator consists of motor and monitoring switch. According to Switch signal of ADM, Door lock actuator
operates motor to lock/unlock door and monitoring switch delivers result to ADM by voltage value.
DTC DESCRIPTION
The ECM sets DTC B2332 if there's short circuit in assist door lock actuator circuit harness.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
Item
Detecting Condition
Possible Cause
DTC Strategy
Check Resistance
short in signal harness
short in power harness
Enable Conditions
IGN `ON' & Engine `OFF'
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:19 PM
Page 205
© 2006 Mitchell Repair Information Company, LLC.
MONITOR DTC STATUS
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Select "Diagnostic Trouble Codes (DTCs) "mode and monitor "DTC Status" parameter.
4. Is the DTC B2332 present?
YES
Go to TERMINAL AND CONNECTOR INSPECTION procedure.
NO
Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and
ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending,
corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to
"VERIFICATION OF VEHICLE REPAIR" procedure.
TERMINAL AND CONNECTOR INSPECTION
1. Many malfunctions in the electrical system are caused by poor harness and terminals.
Faults can also be caused by interference from other electrical systems, and mechanical or chemical
damage.
2. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination,
deterioration, or damage.
3. Has a problem been found?
YES
Repair as necessary and go to "VERIFICATION VEHICLE REPAIR" procedure.
NO
Go to SIGNAL CIRCUIT INSPECTION procedure.
SIGNAL CIRCUIT INSPECTION
1. Check for open in harness
1. Ignition "OFF".
Threshold value
infinity ohms
Faulty door lock actuator
Faulty ADM
Detecting time
50 ms
FAIL SAFE
-
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:19 PM
Page 206
© 2006 Mitchell Repair Information Company, LLC.
2. Disconnect assist Door lock actuator.
3. Measure resistance between terminal "9" of ADM and chassis ground.
Specification: Approx. infinity ohms
Fig. 173: Measuring Resistance Between Terminal 9 Of ADM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured resistance within specifications?
YES
Go to "POWER CIRCUIT INSPECTION" procedure.
NO
Check for short in signal harness. Repair as necessary and go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
POWER SUPPLY CIRCUIT INSPECTION
1. Motor Power circuit Inspection
1. Ignition "OFF"
2. Disconnect assist Door lock actuator.
3. Measure resistance between terminal "5" of ADM and chassis ground.
Specification :Approx. infinity ohms
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:19 PM
Page 207
© 2006 Mitchell Repair Information Company, LLC.
Fig. 174: Measuring Resistance Between Terminal 5 Of ADM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured resistance within specifications?
YES
Go to "COMPONENT INSPECTION" procedure.
NO
Check for short in power harness. Repair as necessary and go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
COMPONENT INSPECTION
1. Check assist Door lock actuator
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF"
3. Select `ACTUATION TEST' mode on scan tool and press [F1] to start
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:19 PM
Page 208
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст