Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 1666
8H–10
SECURITY AND LOCKS
3. Remove the waterproof sheet.
• Remove the waterproof sheet, taking special care
so as not to break it.
4. Remove the hatchgate lock.
• Disconnect the lock link and connector and
remove the 3 fixing bolts.
5. Remove the key cylinder.
• Disconnect the lock links.
• Remove the key cylinder retaining clip with screw
driver to remove the key cylinder.
683RW002
6. Remove the hatchgate lock actuator assembly.
• Disconnect the actuator harness connector.
• Remove the 2 bolts holding hatchgate lock
actuator assembly from inside.
7. Remove the outside handle.
• Remove the 2 bolts holding the outside handle
from inside.
8. Remove the tailgate lock assembly.
• Remove the 3 screws holding the lock assembly.
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. When setting up links, pay attention to the position
and direction of the links.
683RW003
EndOFCallout
2. Apply chassis grease to the lock assembly and
striker moving surface.
3. Check that the tailgate lock operates correctly after
installing it.
4. Tighten the tailgate lock assembly fixing bolts to the
specified torque.
Torque 7 N·m (61 Ib in)
5. Tighten the hatchgate lock assembly fixing bolts to
the specified torque.
Torque 9 N·m (78 Ib in)
Legend
(1) Tailgate Lock Link
(2) Outside Handle
(3) Key Cylinder Link
(4) Cancel Mechanism
SECURITY AND LOCKS
8H–11
Tailgate Lock (SWB)
Tailgate Lock and Associated Parts
681RY00001
EndOFCallout
Removal
1. Disconnect the battery ground cable.
2. Remove the tailgate glass assembly and tailgate
glass stay.
• Refer to Tailgate Glass (SWB) in Body Structure
section.
3. Remove the tailgate trim cover assembly.
• Remove the two screws fixing the trim cover
assembly and pull up the trim cover after
detaching the clips from tailgate panel.
4. Remove the waterproof sheet.
• Remove the waterproof sheet, taking special care
so as not to break it.
5. Remove the key cylinder.
• Disconnect the lock links.
• Remove the key cylinder retaining clip with screw
driver to remove the key cylinder.
6. Remove the hatchgate lock actuator assembly.
• Disconnect the actuator harness connector.
• Remove the two nuts holding hatchgate lock
actuator assembly from inside.
7. Remove the outside handle.
• Disconnect the lock link.
• Remove the two bolts holding the outside handle
from inside.
8. Remove the tailgate lock assembly.
• Remove the three screws holding the lock
assembly.
Legend
(1) Tailgate Assembly
(2) Waterproof sheet
(3) Trim Cover Assembly
(4) Key Cylinder
(5) Tailgate Lock Assembly
(6) Outside Handle
(7) Hatchgate Lock Actuator Assembly
8H–12
SECURITY AND LOCKS
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. Apply chassis grease to the lock assembly and
striker moving surface.
2. Tighten the tailgate lock assembly fixing screws to
the specified torque.
Torque 7 N·m (61 lb in)
3. Check that the tailgate lock operates correctly after
installing it.
SECURITY AND LOCKS
8H–13
Key
Key Coding
730RX001
EndOFCallout
One key is used for the ignition, door, and tailgate lock
cylinders. The keys are cut on both edges to make them
reversible.
Key identification is obtained from the five character key
code stamped on the key code tag. From this key code,
the key code cutting combination can be determined
from a code list (available to owners of key cutting
equipment from suppliers).
If key codes are not available from records or tags, the
key code can be obtained from the right hand door lock
cylinder (if lock has not been replaced). Lock cylinders
supplied by the factory as service parts are unmarked.
If the original key is available, the key code cutting
combination can be determined by laying the key on the
diagram shown in the figure.
Key Styles
730RX002
EndOFCallout
The keys come in styles A or B depending on the key
code cutting combination. When the first position in the
combination is a 1, 2 or 3, Style A is used. When the first
position is a 4, Style B (factory pre-cut key) is used.
Legend
(1) Key (Actual size)
(2) Key Code Tag
(3) Position
(4) Level
Legend
(1) Blank Key Style “A"
(2) Blank Key Style “B"
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст