Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 1665
8H–6
SECURITY AND LOCKS
Rear Door Lock Assembly
Rear Door Lock Assembly and Associated Parts
655R100004
EndOFCallout
Removal
1. Disconnect the battery ground cable.
2. Remove the rear corner garnish.
• Pull the corner garnish to disconnect the retaining
clip.
3. Remove the window regulator handle.
• Remove the clip on the rear side of the regulator
handle using a wire.
651RW003
Legend
(1) Outside Handle
(2) Door Lock Assembly
(3) Bracket
(4) Rear Corner Garnish
(5) Door Trim Panel
(6) Power Window Switch and Pull Case/Window
Regulator Handle
(7) Inside Handle
(8) Waterproof Sheet
SECURITY AND LOCKS
8H–7
4. Remove the screw while pulling the inside lever
toward you and then remove the inside handle.
5. Remove the screw at the pull case.
655R100002
6. Pull out the trim panel at the 8 clip positions.
• Disconnect the power window switch connector.
655R100003
7. Remove the bracket.
8. Peel the upper half of the waterproof sheet.
• Taking notice of the door harness, peel the
waterproof sheet off the door panel carefully.
9. Disconnect the locking links and remove the door
lock assembly fixing screws to remove the door lock
assembly.
652RW002
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Apply chassis grease to the lock assembly and
striker moving surface.
2. Install the regulator handle as shown in the
illustration, if equipped without power windows.
631RW005
3. Tighten the door lock assembly fixing screws to the
specified torque.
Torque 7 N·m (61 Ib in)
4. Check that the door lock operates smoothly.
8H–8
SECURITY AND LOCKS
Rear Outside Handle
Rear Outside Handle and Associated Parts
655R100004
EndOFCallout
Removal
1. Disconnect the battery ground cable.
2. Remove the door trim panel.
• Refer to Rear Door Lock Assembly in this
section.
3. Peel the upper half of the waterproof sheet.
• Taking notice of the door harness, peel the
waterproof sheet off the door panel carefully.
4. Disconnect the locking link and remove fixing bolts
to remove the outside handle.
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Check that the outside handle operates smoothly.
2. Tighten the outside handle fixing bolts to the
specified torque.
Torque 9 N·m (78 Ib in)
Legend
(1) Outside Handle
(2) Door Lock Assembly
(3) Bracket
(4) Rear Corner Garnish
(5) Door Trim Panel
(6) Power Window Switch and Pull Case/Window
Regulator Handle
(7) Inside Handle
(8) Waterproof Sheet
SECURITY AND LOCKS
8H–9
Tailgate Lock and Hatchgate Lock (LWB)
Tailgate Lock, Hatchgate Lock and Associated Parts
681RW005
EndOFCallout
Removal
1. Disconnect the battery ground cable.
2. Remove the tailgate trim cover assembly (3).
• Remove the 2 screws (2) holding the hatchgate
lock assembly (1) first, and pull up the trim cover
while detaching the clips from tailgate panel.
683RW001
Legend
(1) Hatchgate Lock Assembly
(2) Tailgate Assembly
(3) Tailgate Lock Relay Lever
(4) Waterproof sheet
(5) Trim Cover Assembly
(6) Key Cylinder
(7) Tailgate Lock Assembly
(8) Ouside Handle
(9) Hatchgate Lock Actuator Assembly
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст