Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 656
4C–50
DRIVE SHAFT SYSTEM
Reassembly
401RW057
Legend
(1) Sleeve Yoke
(2) Seal
(3) Tube Assembly
1. Discard used seal and install new one.
2. Align the alignment marks and install tube assembly
to sleeve yoke.
4C–51
DRIVE SHAFT SYSTEM
Main Data and Specifications
General Specifications
Engine
6VE1(3.5 L)
Transmission
M/T
A/T
A/T with TOD
Construction
Hollow steel tube with yoke and spider type universal joints.
Outside diameter
68.9 mm (2.71 in)
68.9 mm (2.71 in)
68.9 mm (2.71 in)
Length
1093 mm (43.03 in)
1093 mm (43.03 in)
1075 mm (42.32 in)
Torque Specifications
E04RW006
TRANSFER CASE (STANDARD TYPE)
4D1–1
TROOPER
DRIVELINE/AXLE
TRANSFER CASE (STANDARD TYPE)
CONTENTS
Service Precaution
4D1–1
. . . . . . . . . . . . . . . . . . . . . .
General Description
4D1–2
. . . . . . . . . . . . . . . . . . . . .
Transfer Rear Oil Seal
4D1–4
. . . . . . . . . . . . . . . . . . .
Removal
4D1–4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation
4D1–4
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Case Assembly
4D1–6
. . . . . . . . . . . . . . . . .
Removal
4D1–6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation
4D1–7
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Rear Case Assembly
4D1–9
. . . . . . . . . . . .
Removal
4D1–9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation
4D1–10
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disassembly
4D1–13
. . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair
4D1–14
. . . . . . . . . . . . . . . . . .
Reassembly
4D1–14
. . . . . . . . . . . . . . . . . . . . . . . . . .
Detent, Shift Arm, and Interlock Pin
(Transfer Case Assembly)
4D1–16
. . . . . . . . . . . . . . .
Disassembled View
4D1–16
. . . . . . . . . . . . . . . . . . . .
Disassembly
4D1–17
. . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair
4D1–18
. . . . . . . . . . . . . . . . . .
Reassembly
4D1–18
. . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Case Assembly
4D1–20
. . . . . . . . . . . . . . . . .
Disassembled View
4D1–20
. . . . . . . . . . . . . . . . . . . .
Disassembly
4D1–21
. . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair
4D1–23
. . . . . . . . . . . . . . . . . .
Reassembly
4D1–27
. . . . . . . . . . . . . . . . . . . . . . . . . .
Main Data and Specifications
4D1–33
. . . . . . . . . . . . .
Special Tools
4D1–36
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.
4D1–2 TRANSFER CASE (STANDARD TYPE)
General Description
M/T model
A07RW019
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст