Isuzu N-Series. Service manual — part 89
2-62 CAB AND FRAME
Removal
1. Disconnect the battery ground cable.
2. Sun visor/holder/grommet (Standard cab)
• Remove the 2 mounting screws to remove the
sun visor.
• Pull the sun visor holder while rotating it 45
°.
• Pry the sun visor grommet with a bladed screw-
driver.
3. Room lamp/mirror (Standard cab)
• Pry the room lamp lens with a bladed screw-
driver, and remove the 2 mounting screws of
room mirror to disconnect the connector.
4. Header shelf (High cab, wide cab except limited
model)
• Refer to “Header Shelf” in this Section.
5. Assist grip
• Open the covers at 2 positions and remove the
mounting screws.
6. Coat hanger
• Turn it 45
° for removal.
7. Fluorescent (Option equipment)
• Refer to “Fluorescent Working with Room
Lamp” in Repair Manual for electrical equip-
ment.
8. Roof ventilator grille (High cab/wide cap; option
equipment)
• Refer to “Roof Ventilator” in this Section.
9. Front grip/front pillar trim cover
• Refer to “Front Pillar Trim Cover” in this Sec-
tion.
10. Rear upper trim cover
• Refer to “Rear Side Trim Cover” in this Section.
11. Clip
• Standard cab; Top: 3 positions, Rear: 2 posi-
tions
• High cab, wide cab; Top: 3 positions, Front: 4
positions (High cab), 5 positions (Wide cab),
Rear 3 positions
12. Rear retainer/clip (High cab, wide cab)
• Remove the clip to remove the retainer.
13. Body side finisher (upper)
• Pull only the upper side from panel flange.
14. Head lining
15. Insulator
Installation
For installation, reverse the removal procedure.
Head Lining (B Pack Model)
Component
N2A0102E
CAB AND FRAME 2-63
Removal
1. Retainer/clip
• Remove the clip to remove the retainer.
2. Clip
3. Head lining
4. Insulator
Installation
For installation, reverse the removal procedure.
Head Lining (Crew Cab Model)
Removal
1. Roof reinforcement
• Remove the 3 left fixing bolts and 3 right fixing
bolts.
2. Retainer
• Remove the 5 front clips and 5 back clips.
3. Head lining
• Remove the 5 front clips and 5 back clips.
4. Insulator
Installation
For installation, reverse the removal procedure.
1. When installing the insulator, be sure to use a new
two-sided adhesive tape.
2. Install the head lining (2) by nipping it with the front
and back retainers (1) and the central reinforce-
ment (3).
Legend
1. Insulator
3. Clip
2. Head lining
4. Retainer/clip
Legend
1. Roof reinforcement
3. Head lining
2. Retainer
4. Insulator
N2A0103E
N2A0104E
2-64 CAB AND FRAME
Roof Ventilator
Removal
1. Roof ventilator grille (1)
• Remove the one mounting screw (3) and pull
out the clips (2) at 4 positions.
2. Roof ventilator mounting nut
• Remove the nuts at 4 positions.
3. Roof ventilator assembly
• Align the main unit with the inlet side and re-
move it from the stud. Turn it 90
° and pull it out.
Installation
For installation, reverse the removal procedure.
N2A0105E
N2A0106E
N2A0107E
CAB AND FRAME 2-65
SEAT BELT
Tongue Side Seat Belt (Single Cab Model)
Component
Removal
1. Seat belt lower anchor bolt
2. Rear pillar lower trim cover
3. Through anchor cover
4. Seat belt upper anchor bolt
5. Retractor fixing bolt
• Remove the bolt and pull out the upper bracket
of the retractor from the panel.
Installation
For installation, reverse the removal procedure taking
the following points into consideration.
1. Tighten the seat belt upper anchor bolt to the spec-
ified torque.
Tighten:
Anchor bolt to 44 N
⋅m (4.5 kg⋅m/32.5 lb⋅ft)
Legend
1. Seat belt upper anchor bolt
5. Bracket
2. Tongue side seat belt assembly
6. Clip
3. Seat belt lower anchor bolt
7. Rear piller lower trim cover
4. Retractor bolt
8. Through anchor cover
N2A0237E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст