Nissan Pathfinder (2005 year). Instruction — part 394
SUSPENSION ARM
RSU-15
C
D
F
G
H
I
J
K
L
M
A
B
RSU
2005 Pathfinder
Inspection
EES001AT
●
Check the suspension arm for damage, cracks, deformation and
replace if necessary.
●
Check the rubber bushing for damage, cracks and deformation.
Replace suspension arm assembly if necessary.
●
Check the ball joint. Replace the suspension arm assembly if
any of the following exists:
–
Ball stud is worn.
–
Joint is hard to swing.
–
Play in axial direction is excessive.
●
Before checking, turn the ball joint at least 10 revolutions so that
the ball joint is properly broken in.
Swinging force “A”
: Refer to
.
Turning force “B”
: Refer to
.
Vertical end play “C”
: Refer to
.
Height “D”
: Refer to
.
WEIA0131E
RSU-16
FRONT LOWER LINK
2005 Pathfinder
FRONT LOWER LINK
PFP:55110
Removal and Installation
EES001AU
REMOVAL
1.
Remove the wheel and tire assembly using power tool.
2.
Remove the stabilizer bar. Refer to
.
3.
Set a suitable jack under the RH rear lower link to relieve the coil
spring tension.
NOTE:
LH side shown, RH side similar.
4.
Remove the RH shock absorber lower end bolt.
NOTE:
LH side shown, RH side similar.
5.
Remove the adjusting bolt and nut, and the bolt and nut, from the front lower link and rear suspension
member using power tool.
6.
Remove the front lower link pinch bolt and nut on the knuckle
side using power tool.
NOTE:
LH side shown, RH side similar.
7.
Disconnect the front lower link from the knuckle using a soft
hammer.
CAUTION:
Do not damage the ball joint with the soft hammer.
8.
Remove the front lower link.
INSPECTION AFTER REMOVAL
●
Check front lower link and bushing for any deformation, crack, or damage. Replace if necessary.
LEIA0077E
LEIA0110E
LEIA0086E
FRONT LOWER LINK
RSU-17
C
D
F
G
H
I
J
K
L
M
A
B
RSU
2005 Pathfinder
INSTALLATION
Installation is in the reverse order of removal.
●
Tighten the nuts and bolts to specification. Refer to
.
●
Perform the final tightening of the front lower link nuts and bolts (with rubber bushings) under unladen
conditions with tires on level ground.
●
Check the wheel alignment. Refer to
RSU-6, "Wheel Alignment Inspection"
.
Inspection
EES001AV
●
Check suspension arm for damage, cracks, deformation and replace if necessary.
●
Check rubber bushing for damage, cracks and deformation. Replace suspension arm assembly if neces-
sary.
●
Check ball joint. Replace suspension arm assembly if any of the following exists:
–
Ball stud is worn.
–
Joint is hard to swing.
–
Play in axial direction is excessive.
●
Before checking, turn ball joint at least 10 revolutions so that ball
joint is properly broken in.
Swinging force “A”
: Refer to
.
Turning force “B”
: Refer to
.
Vertical end play “C”
: Refer to
.
Height “D”
: Refer to
.
WEIA0131E
RSU-18
REAR LOWER LINK & COIL SPRING
2005 Pathfinder
REAR LOWER LINK & COIL SPRING
PFP:551B0
Removal and Installation
EES001AW
REMOVAL
1.
Remove the wheel and tire assembly using power tool. Refer to
.
2.
If removing the LH rear lower link and coil spring, remove the spare wheel and tire assembly.
3.
Set a suitable jack to relieve the coil spring tension and support
the rear lower link.
4.
Loosen the rear lower link adjusting bolt and nut connected to
the rear suspension member without removing the adjusting bolt
and nut, using power tool.
5.
Remove the rear lower link bolt and nut from the knuckle using
power tool.
6.
Slowly lower the rear lower link using the suitable jack to release the coil spring tension. Then remove the
upper rubber seat, coil spring and lower rubber seat from the rear lower link.
7.
Remove the rear lower link adjusting bolt and nut from the rear
suspension member using power tool, then remove the rear
lower link.
INSTALLATION
Installation is in the reverse order of removal.
●
Tighten the nuts and bolts to specification. Refer to
.
LEIA0077E
LEIA0009E
LEIA0077E
LEIA0009E
REAR LOWER LINK & COIL SPRING
RSU-19
C
D
F
G
H
I
J
K
L
M
A
B
RSU
2005 Pathfinder
●
When installing the upper and lower rubber seats for the rear
coil springs, the arrow embossed on the rubber seats must point
out toward the wheel and tire assembly.
●
Perform the final tightening of the rear lower link nuts and bolts
(with rubber bushings) under unladen conditions with tires on
level ground.
●
Check the wheel alignment. Refer to
.
Inspection
EES001AX
Check for deformation, cracks, or other damage and replace if necessary.
LEIA0076E
RSU-20
STABILIZER BAR
2005 Pathfinder
STABILIZER BAR
PFP:56230
Removal and Installation
EES001AY
REMOVAL
1.
Disconnect the stabilizer bar ends from the connecting rods
using power tool.
2.
Remove the stabilizer bar clamps using power tool, and remove
the stabilizer bar bushings.
3.
Remove the stabilizer bar.
INSTALLATION
Installation is in the reverse order of removal.
●
Tighten the nuts and bolts to specification. Refer to
.
●
Install the stabilizer bar bushings and clamps so they are posi-
tioned outside of the sideslip prevention clamp on the stabilizer
bar.
Inspection
EES001AZ
●
Check stabilizer bar for any deformation, cracks, or damage and replace if necessary.
●
Check rubber bushings for deterioration, or cracks and replace if necessary.
LEIA0111E
LEIA0113E
LEIA0112E
SERVICE DATA AND SPECIFICATIONS (SDS)
RSU-21
C
D
F
G
H
I
J
K
L
M
A
B
RSU
2005 Pathfinder
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Wheel Alignment
EES001B4
Camber
Degree minute (decimal degree)
Minimum
- 0
°
32
′
(- 0.53
°
)
Nominal
- 0
°
2
′
(- 0.03
°
)
Maximum
0
°
28
′
(0.47
°
)
Total toe-in
Distance (A - B)
Minimum
- 1.4 mm (- 0.055 in)
Nominal
1.9 mm (0.075 in)
Maximum
5.2 mm (0.205 in)
Cross toe
0
±
2 mm (0
±
0.079 in)
Angle (left, right)
Degree minute (decimal degree)
Minimum
- 0
°
3' (-0.05
°
)
Nominal
0
°
4' (0.07
°
)
Maximum
0
°
11' (0.18
°
)
SFA234AC
RSU-22
SERVICE DATA AND SPECIFICATIONS (SDS)
2005 Pathfinder
Ball Joint
EES001B5
*: Measurement point is at the bolt groove of the ball stud.
Wheelarch Height (Unladen* )
EES001B6
Unit: mm (in)
*: Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designated positions.
Ball joint position
Upper
Lower
Swinging force* “A”
11.4 - 145.5 N (1.16 - 14.8 kg, 2.56 - 32.7 lb)
11.0 - 140.7 N (1.12 - 14.35 kg, 2.47 - 31.63 lb)
Turning torque “B”
0.5 - 6.4 N·m (0.06 - 0.65 kg-m, 5 - 56 in-lb)
0.5 - 6.4 N·m (0.06 - 0.65 kg-m, 5 - 56 in-lb)
Vertical end play “C”
0 mm (0 in)
0 mm (0 in)
Height “D”
44 mm (1.73 in)
45.5 mm (1.79 in)
WEIA0131E
Drive type
4X2
Part time 4X4
Full time
4X4
Applied model
XE
SE
LE
XE
SE
LE
Tire size
245/75R16
265/70R16
265/75R16
265/65R17
245/75R16
265/70R16
265/75R16
265/65R17
Front wheelarch
height (Hf)
866
(34.09)
867
(34.13)
879
(34.61)
868
(34.17)
874
(34.41)
876
(34.49)
888
(34.96)
878
(34.57)
Rear wheelarch
height (Hr)
875
(34.45)
876
(34.49)
888
(34.96)
877
(34.53)
885
(34.84)
886
(34.88)
898
(35.35)
887
(34.92)
LEIA0085E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст