Nissan Pathfinder (2005 year). Instruction — part 395
SB-1
SEAT BELTS
H RESTRAINTS
CONTENTS
C
D
E
F
G
I
J
K
L
M
SECTION
A
B
SB
2005 Pathfinder
PRECAUTIONS . . . . . . . . . . . . . . .. 2
AFTER A COLLISION . . . . . . . . . . ... 2
SEAT BELTS . . . . . . . . . . . . . . . .. 3
Removal and Installation of Front Seat Belt . . . . 3
Removal and Installation of Rear Seat Belt . . . . 5
Removal and Installation of Third Row Seat Belt . . 7
Seat Belt Inspection . . . . . . . . . . . . .. 9
LATCH (LOWER ANCHORS AND TETHER FOR
CHILDREN) SYSTEM . . . . . . . . . . . ... 12
Removal and Installation . . . . . . . . . . 12
SB-2
PRECAUTIONS
2005 Pathfinder
PRECAUTIONS
PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EHS00123
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Seat Belt Service
EHS00124
CAUTION:
●
Before removing the seat belt pre-tensioner assembly, turn the ignition switch OFF, disconnect
both battery cables and wait at least 3 minutes.
●
After replacing or reinstalling seat belt pre-tensioner assembly, or reconnecting seat belt pre-ten-
sioner assembly connector, ensure entire SRS operates properly. Refer to
.
●
Do not disassemble buckle or seat belt assembly.
●
Do not reuse seat belt anchor bolts after removal. Replace with new ones.
●
Replace anchor bolts if they are deformed or worn out.
●
Never oil tongue and buckle.
●
If any component of seat belt assembly is questionable, do not repair. Replace the whole seat belt
assembly.
●
If webbing is cut, frayed, or damaged, replace seat belt assembly.
●
When replacing seat belt assembly, use a genuine NISSAN seat belt assembly.
AFTER A COLLISION
WARNING:
●
Inspect all seat belt assemblies including retractors and attaching hardware after any collision.
●
NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the
collision was minor and the belts show no damage and continue to operate properly. Failure to do
so could result in serious personal injury in an accident. Seat belt assemblies not in use during a
collision should also be replaced if either damage or improper operation is noted. Seat belt pre-
tensioner should be replaced even if the seat belts are not in use during a frontal collision in which
the air bags are deployed.
Replace any seat belt assembly (including anchor bolts) if:
●
The seat belt was in use at the time of a collision (except for minor collisions and the belts, retractors and
buckles show no damage and continue to operate properly).
●
The seat belt was damaged in an accident. (i.e., torn webbing, bent retractor or guide, etc.)
●
The seat belt attaching point was damaged in an accident. Inspect the seat belt attaching area for damage
or distortion and repair as necessary before installing a new seat belt assembly.
●
Anchor bolts are deformed or worn out.
●
The seat belt pre-tensioner should be replaced even if the seat belts are not in use during the collision in
which the air bags are deployed.
SEAT BELTS
SB-3
C
D
E
F
G
I
J
K
L
M
A
B
SB
2005 Pathfinder
SEAT BELTS
PFP:86884
Removal and Installation of Front Seat Belt
EHS00125
1.
Seat belt height adjuster
2.
Center pillar
3.
Seat belt retractor and belt assembly LH
4.
Seat belt pre-tensioner connector
5.
Center pillar lower finisher 6.
Anchor cover
7.
Seat belt buckle
8.
D-ring anchor bolt cover
9.
D-ring anchor
10. Center pillar upper finisher
LHIA0081E
SB-4
SEAT BELTS
2005 Pathfinder
REMOVAL OF SEAT BELT RETRACTOR
CAUTION:
●
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
1.
Remove the center pillar upper/lower finishers. Refer to
.
2.
Remove the seat belt retractor anchor bolts and assembly.
●
On RH side, disconnect the seat belt tension sensor.
3.
Disconnect the seat belt pre-tensioner electrical connector.
CAUTION:
●
For installing/removing seat belt pre-tensioner connector,
insert a thin screwdriver wrapped in tape into the notch, lift
the lock and remove the connector.
●
Install the connector with the lock raised, and push the lock
into the connector.
INSTALLATION OF SEAT BELT RETRACTOR
Installation is in the reverse order of removal.
●
Install the seat belt retractor upper bolt first.
●
Ensure that seat belt height adjuster is locked in the lowest position during installation.
REMOVAL OF SEAT BELT BUCKLE
1.
Remove the front seat. Refer to
SE-90, "Removal and Installation"
.
2.
Remove screw and seat cushion inner finisher.
3.
Remove the anchor bolt and buckle.
4.
Disconnect the buckle switch connector from the seat connector.
INSTALLATION OF SEAT BELT BUCKLE
Installation is in the reverse order of removal.
PHIA0341E
WHIA0128E
SEAT BELTS
SB-5
C
D
E
F
G
I
J
K
L
M
A
B
SB
2005 Pathfinder
Removal and Installation of Rear Seat Belt
EHS00126
Second Row
LHIA0082E
1.
Seat belt height adjuster
2.
Seat belt retractor and belt assembly
(Outboard)
3.
Seat belt lower anchor
4.
Seat belt buckle (Outboard)
5.
D-ring anchor bolt cover
6.
D-ring anchor
7.
Seat belt buckle (Center)
8.
Seat belt retractor and belt assembly
(Center)
SB-6
SEAT BELTS
2005 Pathfinder
REMOVAL OF SEAT BELT RETRACTOR - OUTBOARD
1.
Remove seat belt lower anchor cover and bolt.
2.
Remove the D-ring anchor bolt cover and D-ring anchor bolt.
3.
Remove the upper and lower luggage area trim. Refer to
.
4.
Remove seat belt retractor anchor bolt and the seat belt assembly.
5.
Remove the seat belt height adjuster assembly.
INSTALLATION OF SEAT BELT RETRACTOR - OUTBOARD
Installation is in the reverse order of removal.
●
Ensure that seat belt height adjuster is locked in the lowest position during installation.
REMOVAL OF SEAT BELT BUCKLE
1.
Remove the rear center seat. Refer to
.
2.
Remove the screw and seat cushion inner finisher. Refer to
96, "Removal and Installation"
.
3.
Remove the anchor bolt and buckle.
4.
Remove the rear outboard seat. Refer to
.
5.
Remove the seat cushion finisher.
6.
Remove the anchor bolt and buckle.
INSTALLATION OF SEAT BELT BUCKLE
Installation is in the reverse order of removal.
REMOVAL OF SEAT BELT RETRACTOR - CENTER SEAT
1.
Remove seat belt anchor.
2.
Remove seat belt bezel.
3.
Remove seat back upholstery and foam. Refer to
SE-96, "Removal and Installation"
.
4.
Remove seat belt retractor cover.
5.
Remove bolt and remove seat belt retractor and seat belt assembly.
INSTALLATION OF SEAT BELT RETRACTOR - CENTER SEAT
Installation is in the reverse order of removal.
WHIA0130E
SEAT BELTS
SB-7
C
D
E
F
G
I
J
K
L
M
A
B
SB
2005 Pathfinder
Removal and Installation of Third Row Seat Belt
EHS00127
Third Row
REMOVAL OF SEAT BELT RETRACTOR AND BUCKLE
1.
Remove the D-ring anchor bolt cover and D-ring anchor bolt.
2.
Remove the lower anchor bolt cover and lower anchor bolt.
3.
Remove the upper and lower luggage side finishers. Refer to
.
4.
Remove the seat belt retractor anchor bolt and retractor and belt assembly.
5.
Remove bolt from seat belt anchor base and remove seat belt buckles.
LHIA0083E
1.
Luggage side upper finisher RH
2.
Seat belt retractor and belt assembly
3.
Seat belt anchor
4.
D-ring anchor
5.
D-ring anchor bolt cover
6.
Seat belt buckle
7.
Lower anchor bolt cover
8.
Luggage side lower finisher RH
SB-8
SEAT BELTS
2005 Pathfinder
INSTALLATION OF SEAT BELT RETRACTOR AND BUCKLE
Installation is in the reverse order of removal.
●
Ensure that seat belt height adjuster is locked in the lowest position during installation.
●
Seat belt anchor base should be flat to the floor during installation and not on the anti-rotation bead.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст