Nissan X-Trail 32. Instruction — part 2117
TM-426
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
PRIMARY SPEED SENSOR
4.
Remove the O-ring
from the primary speed sensor.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to the O-ring.
Inspection and Adjustment
INFOID:0000000010622616
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
If CVT fluid leaks during work, adjust the CVT fluid level. Refer to
.
JSDIA5199ZZ
OUTPUT SPEED SENSOR
TM-427
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OUTPUT SPEED SENSOR
Exploded View
INFOID:0000000010622617
Removal and Installation
INFOID:0000000010622618
REMOVAL
1.
Turn ignition switch OFF.
2.
Disconnect the output speed sensor connector
.
3.
Remove the output speed sensor bolt (
) and remove the out-
put speed sensor
.
Transaxle assembly
Output speed sensor
O-ring
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA5033GB
JSDIA5200ZZ
JSDIA5201ZZ
TM-428
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
OUTPUT SPEED SENSOR
4.
Remove the O-ring
from the output speed sensor.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to the O-ring.
Inspection and Adjustment
INFOID:0000000010622619
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
If CVT fluid leaks during work, adjust the CVT fluid level. Refer to
.
JSDIA5199ZZ
DIFFERENTIAL SIDE OIL SEAL
TM-429
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000010622620
Removal and Installation
INFOID:0000000010622621
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
Differential Side Oil Seal (Left Side)
1.
Remove front drive shaft. Refer to
FAX-36, "MR20DD : Removal and Installation"
(2WD with MR20DD),
FAX-101, "MR20DD : Removal and Installation"
(4WD with MR20DD),
FAX-113, "QR25DE : Removal and
(QR25DE).
2.
Remove differential side oil seal
using oil seal remover (A)
(commercial service tool).
CAUTION:
Be careful not to scratch transaxle case and converter
housing.
Differential Side Oil Seal (Right Side) (2WD Models Only)
1.
Remove front drive shaft. Refer to
FAX-36, "MR20DD : Removal and Installation"
.
Transaxle assembly
Differential side oil seal (left side)
Differential side oil seal (right side)
(2WD models only)
: Always replace after every disassembly.
: Apply CVT fluid
JSDIA3729GB
JPDIA0118ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст