Nissan X-Trail 32. Instruction — part 643
HOOD LOCK
DLK-913
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Remove fuel filler lid opener cable from fuel filler lid opener lever. Refer to
OPENER CABLE : Removal and Installation"
.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, perform hood lock control inspection. Refer to
DLK-911, "HOOD LOCK : Inspection"
.
HOOD LOCK CONTROL CABLE
HOOD LOCK CONTROL CABLE : Removal and Installation
INFOID:0000000010728661
REMOVAL
1.
Remove air duct 1. Refer to
EM-31, "Removal and Installation"
(QR25DE) or
EM-308, "Removal and Installation"
(R9M).
2.
Disconnect hood lock control cable assembly from hood lock assembly. Refer to
3.
Remove fender protector LH. Refer to
EXT-35, "FENDER PROTECTOR : Removal and Installation"
.
4.
Remove hood lock control cable fixing clips.
5.
Disconnect hood lock control cable assembly from hood lock control handle. Refer to
LOCK CONTROL HANDLE : Removal and Installation"
.
6.
Remove dash side finisher LH. Refer to
INT-26, "DASH SIDE FINISHER : Removal and Installation"
.
7.
Remove grommet of the lower dash, and pull the hood lock control cable assembly toward inside vehicle.
CAUTION:
While pulling, never damage (peeling) the outside of hood lock control cable.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• Install grommet in the panel hole surely.
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet
properly.
• After installation, perform hood lock control inspection. Refer to
.
HOOD LOCK BELL CRANK
HOOD LOCK BELL CRANK : Removal and Installation
INFOID:0000000010728662
REMOVAL
JMKIA5814ZZ
DLK-914
< REMOVAL AND INSTALLATION >
[TYPE 4]
HOOD LOCK
1.
Disengage pawls of hood lock bell crank cable and disconnect hood lock bell crank cable
from housing
bracket
of hood lock assembly according to the numerical order 1
→
2 indicated by arrows as shown in
the figure.
2.
Disconnect hood lock bell crank cable
from lever
of hood lock assembly according to the numerical
order 1
→
2 indicated by arrows as shown in the figure.
3.
Remove hood lock bell crank assembly mounting bolts, and then remove hood lock bell crank assembly.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, perform hood lock control inspection. Refer to
DLK-911, "HOOD LOCK : Inspection"
.
: Pawl
: Vehicle front
JMKIB2981ZZ
: Vehicle front
JMKIB2982ZZ
FRONT DOOR LOCK
DLK-915
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR LOCK
Exploded View
INFOID:0000000010728663
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010728664
REMOVAL
1.
Disconnect lock knob cable and inside handle cable from inside handle. Refer to
DLE : Removal and Installation"
2.
Disconnect outside handle cable from outside handle bracket. Refer to
.
3.
Disconnect door lock assembly connector.
4.
Remove door lock assembly TORX bolts, and then remove door lock assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
Outside handle escutcheon
Rear gasket
TORX bolt
Key rod (driver side)
Door lock assembly
Cable clip
Inside handle
Outside handle bracket
Front gasket
Outside handle grip
: Pawl
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
JMKIB3519GB
DLK-916
< REMOVAL AND INSTALLATION >
[TYPE 4]
FRONT DOOR LOCK
CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.
• When installing outside handle cable to outside handle, be careful that outside handle cable is
routed normally.
• When installing key rod, rotate key rod holder until a click is felt.
• After installation, check door lock. Refer to
DLK-916, "DOOR LOCK : Inspection"
.
DOOR LOCK : Inspection
INFOID:0000000010728665
1.
After opening and closing the door, check that door is fixed to the vehicle body normally.
2.
Check the lock/unlock operation of door lock.
3.
Check door lock assembly for poor lubrication. Apply body
grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000010728666
REMOVAL
1.
Remove front door finisher. Refer to
INT-26, "DASH SIDE FINISHER : Removal and Installation"
.
2.
Remove inside handle mounting bolt.
3.
Disengage inside handle
from door panel
while sliding
inside handle toward vehicle rear, and then separate inside han-
dle.
4.
Disengage lock knob cable
and inside handle cable
from
inside handle
according to the numerical order 1
→
4 indicated
by arrows as shown in the figure.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, check door lock. Refer to
DLK-916, "DOOR LOCK : Inspection"
: Body grease
JMKIA8534ZZ
: Pawl
JMKIB3520ZZ
JMKIB3521ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст