Nissan X-Trail 32. Instruction — part 642
BACK DOOR
DLK-909
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Working from the upper section, align back door weather-strip
center mark
with vehicle center posi-
tion mark
and install weather-strip onto the vehicle
.
2.
Align the connecting point
of back door weather-strip
with the center
of back door striker
, and
then install weather-strip onto the vehicle.
3.
Pull back door weather-strip gently to ensure that there is no loose section.
CAUTION:
Check that weather-strip fits tightly in each corner.
: Vehicle front
JMKIB3151ZZ
: Vehicle front
JMKIB3152ZZ
DLK-910
< REMOVAL AND INSTALLATION >
[TYPE 4]
HOOD LOCK
HOOD LOCK
Exploded View
INFOID:0000000010728657
HOOD LOCK
HOOD LOCK : Removal and Installation
INFOID:0000000010728658
REMOVAL
1.
Disconnect hood lock switch harness connector
(if equipped).
Hood lock assembly
Hood lock bell crank assembly
Hood lock control cable assembly
Hood lock control handle assembly
Cable clip
: N·m (kg-m, in-lb)
: Body grease
JMKIB3484GB
: Vehicle front
JMKIB2974ZZ
HOOD LOCK
DLK-911
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2.
Disconnect hood lock bell crank cable from hood lock assembly. Refer to
CRANK : Removal and Installation"
.
3.
Remove hood lock assembly mounting bolts, and then remove hood lock assembly.
4.
Disconnect hood lock control cable assembly
from hood lock
assembly
according to the numerical order 1
→
2 indicated by
arrows as shown in the figure.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• Check that hood lock control cable is properly engaged with hood lock.
• After installation, perform hood fitting adjustment. Refer to
DLK-871, "HOOD ASSEMBLY : Adjust-
• After installation, perform hood lock control inspection. Refer to
.
HOOD LOCK : Inspection
INFOID:0000000010728659
NOTE:
If the hood lock cable is bent or deformed, replace it.
1.
Check that hood opener operating is condition 49 N (5.0 kg, 11.0 lb) or below.
2.
Check that secondary latch
is securely engaged with second-
ary striker
from the dead load of hood assembly.
3.
Check that primary latch
is securely engaged with primary
striker
when hood assembly is closed [free-fall from approxi-
mately 200 mm (7.874 in) height].
4.
While operating the hood opener carefully, check that the front end of the hood is lifted by approximately
20 mm (0.787 in) (A). Also, check that the hood opener returns to the original position.
JMKIB3486ZZ
JMKIB3518ZZ
JMKIB3499ZZ
DLK-912
< REMOVAL AND INSTALLATION >
[TYPE 4]
HOOD LOCK
5.
Check that secondary latch is properly engaged with secondary striker [6.8 mm (0.268 in)] (B).
6.
Check the hood lock lubrication condition. If necessary, apply body grease to hood lock.
• Hood lock assembly
• Hood lock bell crank assembly
HOOD LOCK CONTROL HANDLE
HOOD LOCK CONTROL HANDLE : Removal and Installation
INFOID:0000000010728660
REMOVAL
1.
Remove hood lock control handle mounting bolts, and then remove hood lock control handle.
2.
Remove hood lock control cable
from hood opener lever
according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
Secondary striker
Secondary latch
Primary striker
Primary latch
JMKIB3549ZZ
: Body grease
JMKIB2979ZZ
: Body grease
JMKIB2980ZZ
JMKIB0324ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст