Nissan X-Trail 32. Instruction — part 2216
C1716-00, C1717-00, C1718-00, C1719-00 TIRE PRESSURE SENSOR
WT-37
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
C1716-00, C1717-00, C1718-00, C1719-00 TIRE PRESSURE SENSOR
DTC Description
INFOID:0000000010715078
DTC DETECTION LOGIC
NOTE:
The actual malfunction part may differ from the malfunction part which DTC shows if ID registration is not per-
formed after performing tire rotation or tire/road wheel replacement.
POSSIBLE CAUSE
• Tire pressure sensor
• BCM
DTC CONFIRMATION PROCEDURE
1.
PERFORM SELF DIAGNOSTIC RESULT
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check tire pressure for all wheels and adjust to the specified value. Refer to
3.
Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC “C1716-00”, “C1717-00”, “C1718-00”, or “C1719-00” detected?
YES
>> Proceed to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010715079
1.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Can the tire pressure sensor ID registration be completed?
YES
>> Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to
.
NO
>> Replace applicable tire pressure sensor. Refer to
WT-62, "Removal and Installation"
DTC No.
CONSULT screen item
(Trouble diagnosis content)
DTC Detection Condition
C1716-00
[PRESSDATA ERR] FL
(Pressure data error front left)
Malfunction in the tire pressure data from the front left wheel tire pressure sensor.
C1717-00
[PRESSDATA ERR] FR
(Pressure data error front right)
Malfunction in the tire pressure data from the front right wheel tire pressure sen-
sor.
C1718-00
[PRESSDATA ERR] RR
(Pressure data error rear right)
Malfunction in the tire pressure data from the rear right wheel tire pressure sen-
sor.
C1719-00
[PRESSDATA ERR] RL
(Pressure data error rear left)
Malfunction in the tire pressure data from the rear left wheel tire pressure sensor.
WT-38
< DTC/CIRCUIT DIAGNOSIS >
C1729-00 VEHICLE SPEED SIGNAL
C1729-00 VEHICLE SPEED SIGNAL
DTC Description
INFOID:0000000010715080
DTC DETECTION LOGIC
POSSIBLE CAUSES
• CAN communication
• BCM
• ABS actuator and electric unit (control unit) malfunction
DTC CONFIRMATION PROCEDURE
1.
DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Drive the vehicle.
2.
Stop the vehicle.
3.
Perform self-diagnosis in “AIR PRESSURE MONITOR”.
Is DTC “C1729-00” detected?
YES
>> Proceed to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010715081
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTCs detected?
YES
>> Check the DTCs. Refer to
.
NO
>> GO TO 2.
2.
CHECK BCM INPUT/OUTPUT SIGNAL
Check BCM input/output signal values. Refer to
.
Is the inspection result normal?
YES
>> Check pin terminal and connection of each harness connector for malfunctioning conditions.
NO
BCS-121, "Removal and Installation"
DTC No.
CONSULT screen item
(Trouble diagnosis content)
DTC Detection Condition
C1729-00
VHCL SPEED SIG ERR
(Vehicle speed signal error)
Vehicle speed signal not detected.
C1734-00 CONTROL UNIT
WT-39
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
C1734-00 CONTROL UNIT
DTC Description
INFOID:0000000010715082
DTC DETECTION LOGIC
POSSIBLE CAUSE
BCM
DTC CONFIRMATION PROCEDURE
1.
PERFORM SELF DIAGNOSTIC RESULT
With CONSULT
Perform self-diagnosis in “AIR PRESSURE MONITOR”.
Is DTC “C1734-00” detected?
YES
>> Proceed to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010715083
1.
CHECK BCM HARNESS CONNECTORS
Check BCM harness connectors for damage or loose connections.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace connectors.
2.
CHECK BCM POWER SUPPLY CIRCUIT
Check BCM power supply circuit. Refer to
BCS-114, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK BCM INPUT/OUTPUT SIGNALS
Check BCM input/output signals. Refer to
.
Is the inspection result normal?
YES
>> Check pin terminal and connection of each harness connector for malfunctioning conditions.
NO
>> Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
DTC No.
CONSULT screen item
(Trouble diagnosis content)
DTC Detection Condition
C1734-00
CONTROL UNIT
(Control unit)
TPMS malfunction in BCM.
WT-40
< DTC/CIRCUIT DIAGNOSIS >
C1735-00 IGNITION SIGNAL
C1735-00 IGNITION SIGNAL
DTC Description
INFOID:0000000010715084
DTC DETECTION LOGIC
POSSIBLE CAUSE
BCM
DTC CONFIRMATION PROCEDURE
1.
PERFORM SELF DIAGNOSTIC RESULT
With CONSULT
Perform self-diagnosis in “AIR PRESSURE MONITOR”.
Is DTC “C1735-00” detected?
YES
>> Proceed to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010715085
1.
PERFORM BCM SELF-DIAGNOSIS
Perform self-diagnosis for “BCM”.
Is any DTCs detection?
YES
>> Check the DTCs. Refer to
NO
>> Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
DTC No.
CONSULT screen item
(Trouble diagnosis content)
DTC Detection Condition
C1735-00
IGN CIRCUIT OPEN
(Ignition circuit open)
BCM has detected a mismatch between IGN ON signals.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст