Nissan Versa Note. Instruction — part 222
FUEL FILLER LID OPENER
DLK-173
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Remove fuel filler lid screws (A) and fuel filler lid (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close and lock/unlock operation.
FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and Installation
INFOID:0000000009486686
REMOVAL
1. Remove hood lock/fuel filler lid lock release handle. Refer to
DLK-161, "HOOD LOCK RELEASE HAN-
DLE : Removal and Installation"
2. Disconnect fuel filler lid opener cable (2) from hood lock/fuel
filler lid lock release handle (1).
3. Remove dash side finisher (LH). Refer to
INT-24, "DASH SIDE FINISHER : Removal and Installation"
4. Remove center pillar lower finisher (LH). Refer to
INT-25, "CENTER PILLAR LOWER FINISHER :
.
5. Remove luggage side lower finisher (LH). Refer to
INT-34, "LUGGAGE SIDE LOWER FINISHER :
.
6. Disconnect fuel filler lid opener cable (1) by pulling downward
and then sliding cable end to the side to remove from fuel filler
lid lock assembly (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
FUEL FILLER LID LOCK
ALKIA3199ZZ
JMKIA7999ZZ
JMKIA8139ZZ
DLK-174
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FUEL FILLER LID OPENER
FUEL FILLER LID LOCK : Removal and Installation
INFOID:0000000009486687
REMOVAL
1. Fully open fuel filler lid.
2. Remove luggage side lower finisher (LH). Refer to
INT-34, "LUGGAGE SIDE LOWER FINISHER :
.
3. Disconnect the harness connector from the fuel filler lid lock assemby.
4. Release pawls (A) and remove fuel filler lid lock assembly (1).
CAUTION:
Be careful not to damage gasket (2) when removing.
5. Disconnect fuel filler lid opener cable (1) by pulling downward
and then sliding cable end to the side to remove from fuel filler
lid lock assembly (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
JMKIA8138ZZ
JMKIA8139ZZ
DOOR SWITCH
DLK-175
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR SWITCH
Removal and Installation
INFOID:0000000009486689
REMOVAL
1. Remove the door switch bolt (A).
2. Disconnect the harness connector and remove door switch (1).
INSTALLATION
Installation is in the reverse order of removal.
JMKIA2173ZZ
DLK-176
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
INSIDE KEY ANTENNA
INSIDE KEY ANTENNA
INSTRUMENT CENTER
INSTRUMENT CENTER : Removal and Installation
INFOID:0000000009486690
REMOVAL
1. Remove center console lower. Refer to
IP-20, "Removal and Installation"
.
2. Disconnect the harness connector from the inside key antenna (instrument center).
3. Remove screws (A) and the inside key antenna (instrument cen-
ter) (1).
INSTALLATION
Installation is in the reverse order of removal.
CONSOLE
CONSOLE : Removal and Installation
INFOID:0000000009486691
REMOVAL
1. Remove center console assembly. Refer to
IP-18, "Removal and Installation"
2. Disconnect the harness connector from the inside key antenna (console).
3. Release clips (A) and remove inside key antenna (console) (1).
INSTALLATION
Installation is in the reverse order of removal.
LUGGAGE ROOM
LUGGAGE ROOM : Removal and Installation
INFOID:0000000009486692
REMOVAL
1. Remove rear seat cushion. Refer to
SE-30, "SEAT CUSHION : Removal and Installation"
.
2. Disconnect the harness connector from the inside key antenna (luggage room).
JMKIA7948ZZ
JMKIA7950ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст