Nissan Versa Note. Instruction — part 830
TM-200
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P1586 G SENSOR
4. Select “G SEN SLOPE”.
5. Swing the vehicle and check if value varies between
−40.45% and 40.45%.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
G SENSOR CALIBRATION (PART 1)
With CONSULT
1. Select “Self Diagnostic Results” in “TRANSMISSION”.
2. Touch “Erase”.
>> Perform "G SENSOR CALIBRATION". Refer to
3.
CHECK SENSOR POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect G sensor connector.
3. Turn ignition switch ON.
4. Check voltage between G sensor harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 8.
4.
CHECK CIRCUIT BETWEEN TCM AND G SENSOR (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check continuity between TCM harness connector terminals and G sensor harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CHECK CIRCUIT BETWEEN TCM AND G SENSOR (PART 2)
Check continuity between TCM harness connector terminals and ground.
Is the inspection result normal?
Monitor item
Condition
Standard
G SEN SLOPE
Flat road
0%
Uphill
Positive value (Maximum 40.45%)
Downhill
Negative value (Minimum
−40.45%)
+
−
Voltage
(Approx.)
G sensor
Connector
Terminal
M83
3
Ground
5.0 V
TCM
G sensor
Continuity
Connector
Terminal
Connector
Terminal
F44
11
M83
2
Existed
14
1
TCM
—
Continuity
Connector
Terminal
F44
14
Ground
Not existed
P1586 G SENSOR
TM-201
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning parts.
6.
CHECK G SENSOR
1. Remove G sensor.
TM-239, "Removal and Installation"
2. Connect the all connectors.
3. Turn ignition switch ON.
4. Check voltage between TCM harness connector terminal and
ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace G sensor.
TM-239, "Removal and Installation"
.
7.
G SENSOR CALIBRATION (PART 2)
With CONSULT
1. Install G sensor.
TM-239, "Removal and Installation"
.
2. Select “Self Diagnostic Results” in “TRANSMISSION”.
3. Touch “Erase”.
>> Perform "G SENSOR CALIBRATION". Refer to
8.
CHECK SENSOR POWER SUPPLY CIRCUIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check continuity between TCM harness connector terminal and G sensor harness connector terminal.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace malfunctioning parts.
9.
CHECK SENSOR POWER SUPPLY CIRCUIT (PART 2)
Check continuity between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
: Direction of gravitational force
+
−
Condition
Voltage
(Approx.)
TCM
Connector
Terminal
F44
14
Ground
Vertical (
−1G) (A)
1.17 V
Horizontal (B)
2.5 V
Vertical (1G) (C)
3.83 V
SCIA8343J
TCM
G sensor
Continuity
Connector
Terminal
Connector
Terminal
F44
26
M83
3
Existed
TCM
—
Continuity
Connector
Terminal
F44
26
Ground
Not existed
TM-202
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P1588 G SENSOR
P1588 G SENSOR
DTC Logic
INFOID:0000000009019743
DTC DETECTION LOGIC
NOTE:
DC stands for "DRIVING CYCLE" and indicates a series of driving cycle of "Ignition switch OFF
→ ON → driv-
ing
→ OFF".
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Start the engine.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “G SPEED”.
4. Drive the vehicle.
5. Maintain the following conditions for 10 seconds or more.
6. Stop the vehicle.
CAUTION:
Never stop the engine.
7. Repeat steps 4 through 6.
8. Check the DTC.
Is “P1588” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009019744
1.
CHECK G SENSOR SIGNAL
With CONSULT
1. Park the vehicle on a level surface.
2. Turn ignition switch ON.
3. Select “Data Monitor” in “TRANSMISSION”.
4. Select “G SEN SLOPE”.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P1588
G Sensor Circuit Range/Per-
formance
When the following diagnosis conditions are
satisfied and the detection conditions are sat-
isfied twice in the same DC:
• Diagnosis condition (1 second or more)
- The rate of change in G sensor detection
value (mV): Between
−15 and +15 inclusive
• Detection condition
- The rate of change in acceleration/deceler-
ation stays +0.0273 G or more/
−0.0273 or
less at least for 5 seconds or more.
G sensor
Selector lever
: “D” position
G SPEED
: 0.05 G or more
P1588 G SENSOR
TM-203
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5. Swing the vehicle and check if value varies between
−40.45% and 40.45%.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
G SENSOR CALIBRATION (PART 1)
With CONSULT
1. Select “Self Diagnostic Results” in “TRANSMISSION”.
2. Touch “Erase”.
>> Perform "G SENSOR CALIBRATION". Refer to
3.
CHECK G SENSOR
1. Remove G sensor.
TM-239, "Removal and Installation"
2. Connect the all connectors.
3. Turn ignition switch ON.
4. Check voltage between TCM harness connector terminal and
ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace G sensor.
TM-239, "Removal and Installation"
.
4.
G SENSOR CALIBRATION (PART 2)
With CONSULT
1. Install G sensor.
TM-239, "Removal and Installation"
.
2. Select “Self Diagnostic Results” in “TRANSMISSION”.
3. Touch “Erase”.
>> Perform "G SENSOR CALIBRATION". Refer to
Monitor item
Condition
Standard
G SEN SLOPE
Flat road
0%
Uphill
Positive value (Maximum 40.45%)
Downhill
Negative value (Minimum
−40.45%)
: Direction of gravitational force
+
−
Condition
Voltage
(Approx.)
TCM
Connector
Terminal
F44
14
Ground
Vertical (
−1G) (A)
1.17 V
Horizontal (B)
2.5 V
Vertical (1G) (C)
3.83 V
SCIA8343J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст