Nissan Almera Tino V10. Instruction — part 99
AT-120
[EURO-OBD]
DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT
After the repair, perform the following procedure to confirm the malfunction is eliminated.
With CONSULT-II
1.
Turn ignition switch “ON” and select “DATA MONITOR” mode for
“ENGINE” with CONSULT-II.
2.
Start engine and maintain the following conditions for at least 10
minutes (Total). (It is not necessary to maintain continuously.)
CMPS·RPM (REF): 450 rpm or more
VHCL SPEED SE: 10 km/h (6 MPH) or more
THRTL POS SEN: More than 1.2V
Selector lever: D position (OD “ON”)
3.
If DTC is detected, go to
AT-122, "Diagnostic Procedure"
.
With GST
Follow the procedure “With CONSULT-II”.
SAT014K
SAT020K
DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT
AT-121
[EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Wiring Diagram — AT — FTS
ECS0097G
YAT370A
AT-122
[EURO-OBD]
DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT
Diagnostic Procedure
ECS0097H
1.
INSPECTION START
Do you have CONSULT-II?
Yes or No
Yes
>> GO TO 2
No
>> GO TO 3
2.
CHECK INPUT SIGNAL OF A/T FLUID TEMPERATURE SENSOR (WITH CONSULT-II)
With CONSULT-II
1.
Start engine.
2.
Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for
“A/T” with CONSULT-II.
3.
Read out the value of “FLUID TEMP SE”.
OK or NG
OK
>> GO TO 4
NG
>> GO TO 5
SAT014K
Voltage:
Cold [20
°
C (68
°
F)]
→
Hot [80
°
C (176
°
F)]
Approximately 1.5V
→
0.5V
SAT614J
DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT
AT-123
[EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
3.
CHECK INPUT SIGNAL OF A/T FLUID TEMPERATURE SENSOR (WITHOUT CONSULT-II)
Without CONSULT-II
1.
Start engine.
2.
Check voltage between TCM terminal 47 and ground while warming up A/T.
3.
Turn ignition switch to “OFF” position.
4.
Disconnect TCM harness connector.
5.
Check continuity between terminal 42 and ground.
If OK, check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 4
NG
>> GO TO 5
4.
CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure,
AT-119, "DIAGNOSTIC TROUBLE CODE
.
OK or NG
OK
>> INSPECTION END
NG
>> 1. Perform TCM input/output signal inspection.
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
5.
CHECK A/T FLUID TEMPERATURE SENSOR WITH TERMINAL CORD ASSEMBLY
1.
Turn ignition switch to “OFF” position.
2.
Disconnect terminal cord assembly connector in engine compartment.
3.
Check resistance between terminals 6 and 7 when A/T is cold.
4.
Reinstall any part removed.
OK or NG
OK (With CONSULT-II)>>GOTO2
OK (Without CONSULT-II)>>GOTO3
NG
>> 1. Remove oil pan.
2. Check the following items:
–
A/T fluid temperature sensor
Refer to
AT-124, "Component Inspection"
.
–
Harness of terminal cord assembly for short or open
Voltage:
Cold [20
°
C (68
°
F)]
→
Hot [80
°
C (176
°
F)]
Approximately 1.5V
→
0.5V
SCIA0738E
Continuity should exist.
SCIA0739E
Resistance:
Cold [20
°
C (68
°
F)]
Approximately 2.5 k
Ω
MCIA0069E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст