Nissan Murano. Instruction — part 804
HA-52
< REMOVAL AND INSTALLATION >
LIQUID TANK
LIQUID TANK
Exploded View
INFOID:0000000009718654
Removal and Installation
INFOID:0000000009718655
REMOVAL
1.
Use refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove front grille. Refer to
.
3.
Clean liquid tank and its surrounding area. Then remove dust and rust from liquid tank.
CAUTION:
Be sure to clean carefully.
4.
Disconnect refrigerant pressure sensor connector (A).
1.
Condenser pipe assembly
2.
O-ring
3.
Condenser assembly
4.
Condenser lower bracket LH
5.
Bracket
6.
Liquid tank
7.
Refrigerant pressure sensor
8.
Liquid tank bracket
9.
Condenser upper bracket LH
10. Condenser upper bracket RH
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JPIIA0460GB
JPIIA0543ZZ
LIQUID TANK
HA-53
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
5.
Remove mounting bolts (A) and then remove liquid tank (1).
CAUTION:
Cap or wrap the joint of the A/C piping and liquid tank with
suitable material such as vinyl tape to avoid the entry of air.
INSTALLATION
Note the following items and then install in the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant.
JPIIA0545ZZ
HA-54
< REMOVAL AND INSTALLATION >
REFRIGERANT PRESSURE SENSOR
REFRIGERANT PRESSURE SENSOR
Exploded View
INFOID:0000000009718656
Removal and Installation
INFOID:0000000009718657
REMOVAL
1.
Remove liquid tank. Refer to
.
2.
Fix the liquid tank (1) with a vise (A). Remove refrigerant pres-
sure sensor (2) with a wrench (B).
CAUTION:
• Be careful not to damage liquid tank.
• Seal the refrigerant pressure sensor on liquid tank with
caps, vinyl tape, or a similar item to prevent them from
being exposed to the atmosphere.
INSTALLATION
Note the following items and then install in the reverse order of removal.
CAUTION:
• Replace the O-rig with a new one. Apply a coat of compressor oil to the O-ring prior to installation.
• Check for leakages when recharging refrigerant.
1.
Condenser pipe assembly
2.
O-ring
3.
Condenser assembly
4.
Condenser lower bracket LH
5.
Bracket
6.
Liquid tank
7.
Refrigerant pressure sensor
8.
Liquid tank bracket
9.
Condenser upper bracket LH
10. Condenser upper bracket RH
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JPIIA0460GB
JSIIA0075ZZ
EVAPORATOR PIPE ASSEMBLY
HA-55
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
EVAPORATOR PIPE ASSEMBLY
Exploded View
INFOID:0000000009718658
HA-14, "Refrigerant Connection"
.
Removal and Installation
INFOID:0000000009718659
REMOVAL
1.
Set the temperature at full cold.
CAUTION:
The angle may be out, when installing the air mix door motor to the air mix door, unless the above
procedure is performed.
2.
Disconnect battery cable from the negative terminal.
3.
Use refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
1.
High-pressure pipe
2.
O-ring
3.
Condenser assembly
4.
High-pressure flexible hose
5.
Compressor
6.
Low-pressure flexible hose
7.
Low-pressure pipe
8.
Heater & cooling unit assembly
9.
Evaporator pipe assembly
10. Expansion valve
11.
Evaporator
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
JPIIA1257GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст