Nissan Murano. Instruction — part 426
RADIATOR CORE SUPPORT
DLK-315
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
15. Remove radiator and engine coolant reservoir tank. Refer to
CO-17, "Removal and Installation"
.
CAUTION:
Operate with two workers, because of it is heavy weight.
16. Disconnect connectors of the following parts.
• Ambient sensor. Refer to
VTL-26, "Removal and Installation"
• Cooling fan (RH/LH) and cooling fan control module. Refer to
• Crash zone sensor. Refer to
SR-22, "Removal and Installation"
17. Remove radiator upper hose from radiator core support. Refer to
18. Remove mounting bolt (A) of radiator lower hose bracket (1).
19. Remove radiator lower hose clamp (A) from radiator core sup-
port.
20. Remove power steering oil cooler pipe (1) from radiator core
support.
21. Remove power steering oil cooler pipe clips.
22. Remove all harness clips from radiator core support.
23. Remove mounting bolts, and then remove radiator core support.
CAUTION:
Never damage power steering oil cooler pipe.
24. Remove the following parts after removing radiator core support.
• Ambient sensor. Refer to
VTL-26, "Removal and Installation"
• Cooling fan (RH/LH) and cooling fan control module. Refer to
• Crash zone sensor. Refer to
SR-22, "Removal and Installation"
INSTALLATION
Install in the reverse order of removal.
: Vehicle front
JMKIA1915ZZ
: Clip
JMKIA1916ZZ
DLK-316
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT FENDER
FRONT FENDER
Exploded View
INFOID:0000000009719222
Removal and Installation
INFOID:0000000009719223
CAUTION:
Use a shop cloth to protect the body from being damaged during removal and installation.
REMOVAL
1.
Remove clips and remove front fender seal (front/rear).
2.
Remove front grille. Refer to
EXT-21, "Removal and Installation"
3.
Remove front bumper fascia. Refer to
EXT-15, "Removal and Installation"
.
4.
Remove front combination lamp. Refer to
EXL-179, "Removal and Installation"
(HALOGEN TYPE).
5.
Remove fender protector. Refer to
EXT-26, "FENDER PROTECTOR : Removal and Installation"
1.
Front fender seal (front)
2.
Front fender seal (rear)
3.
Front fender assembly
4.
Front fender finisher
5.
Insulator
: Clip
: Pawl
JMKIA1806ZZ
FRONT FENDER
DLK-317
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
6.
Using remover tool (A), remove front fender finisher (1).
7.
Disengage front part of windshield glass molding from front fender.
8.
Remove mounting bolts and remove front fender.
CAUTION:
An viscous urethane foam is installed on the back surface of front fender. When removing the
front fender, peel of the urethane foam bit at a time, and carefully to remove it.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• After installation, check front fender adjustment. Refer to
DLK-309, "HOOD ASSEMBLY : Adjust-
DLK-319, "DOOR ASSEMBLY : Adjustment"
.
• After installation, apply the touch-up paint (the body color) onto the head of front fender mounting
bolts.
: Clip
: Pawl
JMKIA2261ZZ
DLK-318
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR
FRONT DOOR
DOOR ASSEMBLY
DOOR ASSEMBLY : Exploded View
INFOID:0000000009719224
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000009719225
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove mounting bolts of door check link on the vehicle.
2.
Remove front door harness grommet, and then pull out the harness from the vehicle.
3.
Disconnect front door harness connector.
4.
Remove door hinge mounting nuts (door side), and then remove door assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-319, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3688ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст