Nissan Tiida C11. Instruction — part 1276
SYSTEM SYMPTOM
TM-155
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
A/T Does Not Shift: D
3
→
2
2
, When Selector Lever "D"
→
"2" Position
INFOID:0000000001696258
SYMPTOM:
A/T does not shift from D
3
to 2
2
when changing selector lever from “D” to “2” position on “Cruise Test
— Part 3”.
1.
CHECK SYMPTOM
Check symptom. Refer to
TM-183, "Cruise Test - Part 1"
TM-185, "Cruise Test - Part 2"
.
Is “A/T Does Not Shift: D
1
→
D
2
or Does Not Kickdown: D
4
→
D
2
” OK?
YES (With CONSULT-II) >>GO TO 2.
YES (Without CONSULT-II) >>GO TO 3.
NO
>> GO TO
TM-146, "A/T Does Not Shift: D
.
2.
CHECK PNP SWITCH CIRCUIT
With CONSULT-II
1.
Turn ignition switch ON. (Do not start engine.)
2.
Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-II.
3.
Read out “P·N”, “R”, “D”, “2” and “1” position switches moving selector lever to each position.
OK or NG
OK
>> INSPECTION END
NG
>> Check PNP switch circuit. Refer to
3.
CHECK PNP SWITCH CIRCUIT
Without CONSULT-II
1.
Turn ignition switch ON. (Do not start engine.)
Monitor item
Condition
Display value
PN POSI SW
When setting selector lever to “N” or “P” posi-
tion.
ON
When setting selector lever to other positions.
OFF
R POSITION SW
When setting selector lever to “R” position.
ON
When setting selector lever to other positions.
OFF
D POSITION SW
When setting selector lever to “D” positions.
ON
When setting selector lever to other positions.
OFF
2 POSITION SW
When setting selector lever to “2” position.
ON
When setting selector lever to other positions.
OFF
1 POSITION SW
When setting selector lever to “1” position.
ON
When setting selector lever to other positions.
OFF
TM-156
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
SYSTEM SYMPTOM
2.
Check voltage between TCM connector terminals and ground
while moving selector lever through each position.
B: Battery voltage
0: 0V
OK or NG
OK
>> INSPECTION END
NG
>> Check PNP switch circuit. Refer to
.
A/T Does Not Shift: 2
2
→
1
1
, When Selector Lever "2"
→
"1" Position
INFOID:0000000001696259
SYMPTOM:
A/T does not shift from 2
2
to 1
1
when changing selector lever from “2” to “1” position on “Cruise Test
— Part 3”.
1.
CHECK PNP SWITCH CIRCUIT
With CONSULT-II
1.
Turn ignition switch ON. (Do not start engine.)
2.
Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-II.
3.
Read out “P·N”, “R”, “D”, “2” and “1” position switches moving selector lever to each position.
OK or NG
OK
>> GO TO 3
NG
>> Check PNP switch circuit. Refer to
.
Selector lever position
Terminal
36
35
34
27
26
“P”, “N”
B
0
0
0
0
“R”
0
B
0
0
0
“D”
0
0
B
0
0
“2”
0
0
0
B
0
“1”
0
0
0
0
B
SCIA7162E
Monitor item
Condition
Display value
PN POSI SW
When setting selector lever to “N” or “P” posi-
tion.
ON
When setting selector lever to other positions.
OFF
R POSITION SW
When setting selector lever to “R” position.
ON
When setting selector lever to other positions.
OFF
D POSITION SW
When setting selector lever to “D” positions.
ON
When setting selector lever to other positions.
OFF
2 POSITION SW
When setting selector lever to “2” position.
ON
When setting selector lever to other positions.
OFF
1 POSITION SW
When setting selector lever to “1” position.
ON
When setting selector lever to other positions.
OFF
SYSTEM SYMPTOM
TM-157
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
CHECK PNP SWITCH CIRCUIT
Without CONSULT-II
1.
Turn ignition switch ON. (Do not start engine.)
2.
Check voltage between TCM connector terminals and ground
while moving selector lever through each position.
B: Battery voltage
0: 0V
OK or NG
OK
>> GO TO 3
NG
>> Check PNP switch circuit. Refer to
3.
CHECK A/T POSITION
Check A/T position. Refer to
TM-204, "Checking of A/T Position"
OK or NG
OK
>> GO TO 4.
NG
>> Adjust A/T position. Refer to
TM-204, "Adjustment of A/T Position"
.
4.
CHECK VEHICLE SPEED SENSOR·A/T AND VEHICLE SPEED SENSOR·MTR CIRCUIT
Check vehicle speed sensor·A/T (revolution sensor) and vehicle speed sensor·MTR circuit. Refer to
XX-XX,
"*****"
(type 1) or
XX-XX, "*****"
(type 2) and
XX-XX, "*****"
(type 1) or
XX-XX, "*****"
(type 2).
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace vehicle speed sensor·A/T (revolution sensor) and vehicle speed sensor·MTR
circuits.
5.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
2.
Check A/T fluid condition. Refer to
.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
TM-191, "Control Valve Assembly and Accumulators"
2.
Check the following items:
-
Shift valve A
-
Shift solenoid valve A
Selector lever position
Terminal
36
35
34
27
26
“P”, “N”
B
0
0
0
0
“R”
0
B
0
0
0
“D”
0
0
B
0
0
“2”
0
0
0
B
0
“1”
0
0
0
0
B
SCIA7162E
TM-158
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
SYSTEM SYMPTOM
-
Overrun clutch control valve
-
Overrun clutch solenoid valve
3.
Disassemble A/T. Refer to
4.
Check the following items:
-
Servo piston assembly
-
Brake band
OK or NG
OK
>> GO TO 7.
NG
>> Repair or replace damaged parts.
7.
CHECK SYMPTOM
Check again. Refer to
TM-186, "Cruise Test - Part 3"
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 8.
8.
CHECK TCM
1.
Check TCM input/output signals. Refer to
TM-22, "Input/Output Signal of TCM"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Vehicle Does Not Decelerate by Engine Brake
INFOID:0000000001696260
SYMPTOM:
• Vehicle does not decelerate by engine brake when shifting from 2
2
(1
2
) to 1
1
“Cruise Test — Part 3”.
• Vehicle does not decelerate by engine brake when OD OFF (OD OFF indicator lamp is on) on “Cruise
Test — Part 3”.
• Vehicle does not decelerate by engine brake when shifting A/T from “D” to “2” position on “Cruise
Test — Part 3”.
1.
CHECK CAN COMMUNICATION LINE
Perform self-diagnosis. Refer to
XX-XX, "*****"
or
TM-38, "Diagnosis Procedure without CONSULT-III"
.
Is a malfunction in CAN communication indicated in the results?
YES
>> Check CAN communication line. Refer to
XX-XX, "*****"
(type 1) or
XX-XX, "*****"
(type 2).
NO
>> GO TO 2.
2.
CHECK OVERDRIVE CONTROL SWITCH CIRCUIT
With CONSULT-II
1.
Turn ignition switch ON. (Do not start engine)
2.
Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-II.
3.
Read out “OVERDRIVE SW”.
Check the signal of the overdrive control switch is indicated properly.
Without CONSULT-II
SAT778B
Item name
Overdrive control switch
Condition
Display value
OVERDRIVE SW
Depressed
ON
Released
OFF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст