Nissan Tiida C11. Instruction — part 1277
SYSTEM SYMPTOM
TM-159
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1.
Turn ignition switch ON. (Do not start engine)
2.
Check voltage between A/T device harness connector terminal
and ground.
OK or NG
OK (With CONSULT-II)>>GO TO 3.
OK (Without CONSULT-II)>>GO TO 4.
NG
>> Check overdrive control switch circuit. Refer to
XX-XX, "*****"
(type 1) or
XX-XX, "*****"
(type 2).
3.
CHECK PNP SWITCH CIRCUIT
With CONSULT-II
1.
Turn ignition switch ON. (Do not start engine.)
2.
Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for
“A/T” with CONSULT-II.
3.
Read out “P·N”, “R”, “D”, “2” and “1” position switches moving
selector lever to each position.
OK or NG
OK
>> GO TO 5
NG
>> Check PNP switch circuit. Refer to
4.
CHECK PNP SWITCH CIRCUIT
Without CONSULT-II
1.
Turn ignition switch ON. (Do not start engine.)
Item
Connector
Terminal
Overdrive
control switch
Condition
Judge-
ment
standard
(Approx.)
A/T device harness
connector (Overdrive
control switch)
M38
1 - Ground
Released
Battery
voltage
Depressed
0V
SCIA5336E
Monitor item
Condition
Display value
PN POSI SW
When setting selector lever to “N” or “P” posi-
tion.
ON
When setting selector lever to other positions.
OFF
R POSITION SW
When setting selector lever to “R” position.
ON
When setting selector lever to other positions.
OFF
D POSITION SW
When setting selector lever to “D” positions.
ON
When setting selector lever to other positions.
OFF
2 POSITION SW
When setting selector lever to “2” position.
ON
When setting selector lever to other positions.
OFF
1 POSITION SW
When setting selector lever to “1” position.
ON
When setting selector lever to other positions.
OFF
SAT701J
TM-160
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
SYSTEM SYMPTOM
2.
Check voltage between TCM connector terminals and ground
while moving selector lever through each position.
B: Battery voltage
0: 0V
OK or NG
OK
>> GO TO 5
NG
>> Check PNP switch circuit. Refer to
XX-XX, "*****"
(type 1) or
XX-XX, "*****"
(type 2).
5.
CHECK A/T POSITION
Check A/T position. Refer to
TM-204, "Checking of A/T Position"
OK or NG
OK
>> GO TO 6.
NG
>> Adjust A/T position. Refer to
TM-204, "Adjustment of A/T Position"
.
6.
CHECK VEHICLE SPEED SENSOR·A/T AND VEHICLE SPEED SENSOR·MTR CIRCUIT
Check vehicle speed sensor·A/T (revolution sensor) and vehicle speed sensor·MTR circuit. Refer to
XX-XX,
"*****"
(type 1) or
XX-XX, "*****"
(type 2) and
XX-XX, "*****"
(type 1) or
XX-XX, "*****"
(type 2).
OK or NG
OK
>> GO TO 7.
NG
>> Repair or replace vehicle speed sensor·A/T (revolution sensor) and vehicle speed sensor·MTR
circuits.
7.
CHECK ACCELERATOR PEDAL POSITION SENSOR
Check accelerator pedal position sensor. Refer to
(type 2).
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace accelerator pedal position sensor.
8.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
2.
Check A/T fluid condition. Refer to
.
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 9.
9.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
TM-191, "Control Valve Assembly and Accumulators"
Selector lever position
Terminal
36
35
34
27
26
“P”, “N”
B
0
0
0
0
“R”
0
B
0
0
0
“D”
0
0
B
0
0
“2”
0
0
0
B
0
“1”
0
0
0
0
B
SCIA7162E
SYSTEM SYMPTOM
TM-161
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
Check the following.
-
Shift valve A
-
Overrun clutch solenoid valve
3.
Disassemble A/T. Refer to
4.
Check the following.
-
Overrun clutch assembly. Refer to
TM-267, "Forward and Overrun Clutches"
.
-
Low & reverse brake assembly. Refer to
.
OK or NG
OK
>> GO TO 10.
NG
>> Repair or replace damaged parts.
10.
CHECK SYMPTOM
TM-186, "Cruise Test - Part 3"
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 11.
11.
CHECK TCM
1.
Check TCM input/output signals. Refer to
TM-22, "Input/Output Signal of TCM"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
TCM Self-Diagnosis Does Not Activate
INFOID:0000000001696261
SYMPTOM:
OD OFF indicator lamp does not come on in TCM self-diagnostic procedure even if the lamp circuit is
good.
DESCRIPTION
• PNP switch
PNP switch assembly includes a transaxle position switch. The
transaxle position switch detects the selector lever position and
sends a signal to the TCM.
• Overdrive control switch
Overdrive control switch detects the switch position (ON or OFF)
and sends a signal to the TCM.
SCIA7141E
SCIA7142E
TM-162
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
SYSTEM SYMPTOM
• Closed throttle position signal and wide open throttle position sig-
nal
ECM judges throttle opening based on a signal from accelerator
pedal position sensor, and sends the signal via CAN communica-
tion to the TCM.
DIAGNOSTIC PROCEDURE
NOTE:
The diagnostic procedure includes inspection for the PNP stitch, overdrive control switch, closed throttle posi-
tion signal and wide open throttle position signal circuit. Refer to
TM-115, "Component Inspection"
SCIA7143E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст